Alpine INA-W910 Owner's Manual (english) - Page 51
Setting the Treble Center Frequency
View all Alpine INA-W910 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 51 highlights
Adjusting Balance/Fader Touch [ ] of Balance/Fader, the adjusting screen of Balance/Fader will be displayed. Display example for Balance/Fader Screen A Adjusting the Fader Touch [F] or [R] to adjust the volume of the front and rear speakers. Setting range: F15 to R15 • If an optional IMPRINT audio processor (PXA-H100) is connected to this unit and you have set the 2.2ch (3WAY)/4.2ch (FRONT/REAR/ SUBW.) switch to 2.2ch (3WAY), you cannot adjust the FADER mode. For details, refer to the Owner's Manual of PXA-H100. B Adjusting the Balance Touch [L] or [R] to adjust the sound volume of the left and right speakers. Setting range: L15 to R15 C Adjusting the Balance/Fader Directly Touch and move [ ] to a desired setting. Or touch a desired setting range, and [ ] will move to that location. Touch [L] or [R] of Balance and [F] or [R] of Fader for fine-tuning. Adjusting Bass/Treble You can change the bass/treble frequency emphasis to create your own tonal preference. Touch [ ] to display the Bass/Treble adjusting screen. • Adjustment cannot be performed when Defeat is set to ON. • If OFF is set in "Changing MultEQ mode" (page 71) when the IMPRINT audio processor is connected, the list is not displayed. Setting the Bass level You can emphasize or weaken the bass frequency. Touch [ ] or [ ] of Bass Level to select the desired bass level. Setting range*1: -6 to +6 Setting range: -7 to +7 *1 Setting value will change according to the level value set in Band 1 of P-EQ or G-EQ. Refer to "Adjusting the Parametric Equalizer Curve (P-EQ)" on page 53 or "Adjusting the Graphic Equalizer Curve (GEQ)" on page 53. Setting the Bass Center Frequency The displayed bass frequency is emphasized. Touch [ ] or [ ] of Bass Freq. to select the desired bass center frequency. Setting range: 63 Hz, 80 Hz, 100 Hz, 200 Hz • The operation can be performed only when the P-EQ is selected in "Setting EQ mode" on page 53. • Setting value will change according to the frequency value set in Band 1 of P-EQ. Refer to "Adjusting the Parametric Equalizer Curve (P-EQ)" on page 53. Setting the Bass Bandwidth Changes the boosted bass bandwidth to wide or narrow. A wider setting will boost a wide range of frequencies above and below the center frequency. A narrower setting will boost only frequencies near the center frequency. Touch [ ] or [ ] of Bass Bandwidth to select the desired bass band width. Setting range: Wide1 (Narrow) to Wide4 (Wide) • The operation can be performed only when the P-EQ is selected in "Setting EQ mode" on page 53. • Setting value will change according to the bandwidth value set in Band 1 of P-EQ. Refer to "Adjusting the Parametric Equalizer Curve (P-EQ)" on page 53. Setting the treble level You can emphasize the treble frequency. Touch [ ] or [ ] of Treble Level to select the desired treble level. Setting range*2: -6 to +6 Setting range: -7 to +7 *2 Setting value will change according to the level value set in Band 5 of P-EQ or Band 7 of G-EQ. Refer to "Adjusting the Parametric Equalizer Curve (P-EQ)" on page 53. Setting the Treble Center Frequency The displayed treble frequency is emphasized. Touch [ ] or [ ] of Treble Freq. to select the desired treble center frequency. Setting range: 10 kHz, 12.5 kHz, 16 kHz, 17.5 kHz • The operation can be performed only when the P-EQ is selected in "Setting EQ mode" on page 53. • Setting value will change according to the frequency value set in Band 5 of P-EQ. Refer to "Adjusting the Parametric Equalizer Curve (P-EQ)" on page 53. 51-EN