Brother International SE2000 Operation Manual - Page 23

Important

Get Brother International SE2000 PDF manuals and user guides View all Brother International SE2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Winding/Installing the Bobbin IMPORTANT • Use the plastic bobbin that comes with this machine or bobbins of the same type. The bobbin's height is 11.5 mm (approx. 7/16 inch). SA156 is a Class 15 type bobbin. Winding the bobbin This section describes how to wind thread onto a bobbin. Winding/Installing the Bobbin Memo • By placing the bobbin into the bobbin case in the same orientation that it was on the bobbin winder shaft, the bobbin can be installed with the correct winding direction of the bobbin thread. The "b" mark on one side of the bobbin included with this machine can be used as a reference. 1 GETTING READY Note • When winding the bobbin for sewing utility stitches, use thread appropriate for the fabric that you wish to sew (page 28). Normally, the thread will be the same as what is used for the upper threading. • When winding bobbin for embroidery, be sure to use the recommended bobbin thread for this machine. Open the top cover. a Place the bobbin on the bobbin winder shaft so that the b notch in the bobbin aligns with the spring on the shaft, and then slide the bobbin winder shaft to the right until it snaps into place. 1 Notch a 2 Bobbin winder shaft spring b Remove the spool cap and place the spool of thread for c the bobbin onto the spool pin. Slide the spool onto the spool pin so that the thread unwinds to the front from the bottom. 1 1 The thread unwinds to the front from the bottom. Slide the spool cap onto the spool pin. d Slide the spool cap as far as possible to the right, as shown, with the rounded side on the left. IMPORTANT • If the spool or the spool cap is not installed correctly, the thread may become tangled around the spool pin, and the machine may be damaged. • Three spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the machine may be damaged. When using mini king thread spool, use the thread spool insert (mini king thread spool). 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Winding/Installing the Bobbin
GETTING READY
21
1
Winding the bobbin
This section describes how to wind thread onto a bobbin.
a
Open the top cover.
b
Place the bobbin on the bobbin winder shaft so that the
notch in the bobbin aligns with the spring on the shaft,
and then slide the bobbin winder shaft to the right until
it snaps into place.
c
Remove the spool cap and place the spool of thread for
the bobbin onto the spool pin.
Slide the spool onto the spool pin so that the thread
unwinds to the front from the bottom.
1
The thread unwinds to the front from the bottom.
d
Slide the spool cap onto the spool pin.
Slide the spool cap as far as possible to the right, as
shown, with the rounded side on the left.
Winding/Installing the Bobbin
IMPORTANT
•
Use the plastic bobbin that comes with this
machine or bobbins of the same type. The
bobbin's height is 11.5 mm (approx. 7/16
inch). SA156 is a Class 15 type bobbin.
Note
•
When winding the bobbin for sewing utility stitches,
use thread appropriate for the fabric that you wish
to sew (page 28). Normally, the thread will be the
same as what is used for the upper threading.
•
When winding bobbin for embroidery, be sure to
use the recommended bobbin thread for this
machine.
1
Notch
2
Bobbin winder
shaft spring
a
b
Memo
•
By placing the bobbin into the bobbin case in the
same orientation that it was on the bobbin winder
shaft, the bobbin can be installed with the correct
winding direction of the bobbin thread.
The “b” mark on one side of the bobbin included
with this machine can be used as a reference.
IMPORTANT
•
If the spool or the spool cap is not installed
correctly, the thread may become tangled
around the spool pin, and the machine may be
damaged.
•
Three spool cap sizes are available, allowing
you to choose a spool cap that best fits the size
of spool being used. If the spool cap is too
small for the spool being used, the thread may
catch on the slit in the spool or the machine
may be damaged. When using mini king thread
spool, use the thread spool insert (mini king
thread spool).
1