Brother International SE2000 Operation Manual - Page 36

Using the foot controller

Get Brother International SE2000 PDF manuals and user guides View all Brother International SE2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Sewing Set the fabric under the presser foot. Hold the fabric g and thread with your left hand, and rotate the handwheel counterclockwise or press (Needle position button) to set the needle in the sewing start position. Lower the presser foot. h Adjust the sewing speed with the sewing speed i controller. (when using utility stitches) b a 1 Fast 2 Slow IMPORTANT • Do not press (Thread cutter button) after the threads have been cut. Doing so could tangle the thread or damage the machine. • Do not press (Thread cutter button) when there is no fabric set in the machine. The thread may tangle, possibly resulting in damage. Note • When cutting thread such as nylon monofilament thread, or other decorative threads, use the thread cutter on the left side of the machine. Press the "Start/Stop" button to start sewing. (When j the foot controller is plugged in, slowly press down on the foot controller.) Guide the fabric lightly by hand. Memo • When the foot controller is connected, the "Start/ Stop" button cannot be used to start sewing. Press the "Start/Stop" button again to stop sewing. k (When the foot controller is plugged in, remove your foot from the foot controller.) Press (Thread cutter button) to trim the upper and l bobbin threads. When the needle has stopped moving, raise the presser m foot and remove the fabric. Check the sewing finish. If necessary, adjust the thread n tension. (page 39) ■ Using the foot controller You can also use the foot controller to start and stop sewing. Memo • (For U.S.A. only) Foot controller: Model T This foot controller can be used on the machine with product code 888-K10/L11/L12. The product code is mentioned on the machine rating plate. • When the foot controller is connected, the "Start/ Stop" button cannot be used to start sewing. • Bobbin winding can be started and stopped with the foot controller. • The foot controller cannot be used when embroidering. Turn off the machine. a Insert the foot controller plug into the foot controller b jack on the machine. 1 1 Foot controller jack Turn on the machine. c 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Sewing
34
g
Set the fabric under the presser foot. Hold the fabric
and thread with your left hand, and rotate the
handwheel counterclockwise or press
(Needle
position button) to set the needle in the sewing start
position.
h
Lower the presser foot.
i
Adjust the sewing speed with the sewing speed
controller. (when using utility stitches)
j
Press the “Start/Stop” button to start sewing. (When
the foot controller is plugged in, slowly press down on
the foot controller.)
Guide the fabric lightly by hand.
k
Press the “Start/Stop” button again to stop sewing.
(When the foot controller is plugged in, remove your
foot from the foot controller.)
l
Press
(Thread cutter button) to trim the upper and
bobbin threads.
m
When the needle has stopped moving, raise the presser
foot and remove the fabric.
n
Check the sewing finish. If necessary, adjust the thread
tension. (page 39)
■
Using the foot controller
You can also use the foot controller to start and stop
sewing.
a
Turn off the machine.
b
Insert the foot controller plug into the foot controller
jack on the machine.
c
Turn on the machine.
1
Fast
2
Slow
Memo
•
When the foot controller is connected, the “Start/
Stop” button cannot be used to start sewing.
a
b
IMPORTANT
•
Do not press
(Thread cutter button) after
the threads have been cut. Doing so could
tangle the thread or damage the machine.
•
Do not press
(Thread cutter button) when
there is no fabric set in the machine. The
thread may tangle, possibly resulting in
damage.
Note
•
When cutting thread such as nylon monofilament
thread, or other decorative threads, use the thread
cutter on the left side of the machine.
Memo
•
(For U.S.A. only) Foot controller: Model T
This foot controller can be used on the machine
with product code 888-K10/L11/L12. The product
code is mentioned on the machine rating plate.
•
When the foot controller is connected, the “Start/
Stop” button cannot be used to start sewing.
•
Bobbin winding can be started and stopped with
the foot controller.
•
The foot controller cannot be used when
embroidering.
1
Foot controller
jack
1