Brother International SE2000 Operation Manual - Page 44

Sewing various fabric

Get Brother International SE2000 PDF manuals and user guides View all Brother International SE2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Useful Sewing Tips Sewing various fabric ■ Sewing thick fabrics  If the fabric does not fit under the presser foot The presser foot lever can be raised to two different positions. If the fabric does not fit under the presser foot, for example, when sewing together thick fabrics, raise the presser foot lever to its highest position so that the fabric can be placed under the presser foot. Release the presser foot locking pin (black button). d  The presser foot remains level, allowing the fabric to be fed.  After the seam is sewn, the presser foot will return to its original angle. Memo • You may find adjusting the [Presser Foot Pressure] in the settings screen helpful on some thick fabrics.  If the fabric does not feed When sewing thick fabric such as denim or quilting, the fabric may not feed at the start of sewing if the presser foot is not level, as shown below. In this case, use the presser foot locking pin (black button on the left side) of zigzag foot "J" so that the presser foot remains level while sewing, allowing the fabric to be fed smoothly. If the presser foot misalignment is too large, place thick paper or fabric (with the same thickness as the fabric being sewn) under the heel of the presser foot to be able to start sewing smoothly. a CAUTION • Do not sew fabric more than 6 mm (15/64 inch) thick or forcefully push fabric. Otherwise, the needle may break, possibly resulting in injury. ■ Sewing thin fabrics When sewing thin fabrics such as chiffon, the stitching may become misaligned or the fabric may not feed correctly. Move the needle (be sure to use a fine needle) to the furthest left or right hand position so that the fabric does not get pulled down into the feed dog area. If this occurs or there is shrinkage of the stitching, place nonwoven water-soluble stabilizer under the fabric and sew them together. 1 Water-soluble stabilizer (non-woven) b dc 1 1 Sewing direction 2 Misalignment 3 Fabric being sewn 4 Fabric or thick paper Raise the presser foot lever. a Align the beginning of stitching, and then position the b fabric. While holding zigzag foot "J" level, push in and hold c the presser foot locking pin (black button on the left side), and lower the presser foot lever. 1 Presser foot locking pin (black a button) 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Useful Sewing Tips
42
Sewing various fabric
■
Sewing thick fabrics
If the fabric does not fit under the presser foot
The presser foot lever can be raised to two different
positions. If the fabric does not fit under the presser foot,
for example, when sewing together thick fabrics, raise the
presser foot lever to its highest position so that the fabric
can be placed under the presser foot.
If the fabric does not feed
When sewing thick fabric such as denim or quilting, the
fabric may not feed at the start of sewing if the presser foot
is not level, as shown below. In this case, use the presser
foot locking pin (black button on the left side) of zigzag
foot “J” so that the presser foot remains level while sewing,
allowing the fabric to be fed smoothly.
If the presser foot misalignment is too large, place thick
paper or fabric (with the same thickness as the fabric being
sewn) under the heel of the presser foot to be able to start
sewing smoothly.
1
Sewing direction
2
Misalignment
3
Fabric being sewn
4
Fabric or thick paper
a
Raise the presser foot lever.
b
Align the beginning of stitching, and then position the
fabric.
c
While holding zigzag foot “J” level, push in and hold
the presser foot locking pin (black button on the left
side), and lower the presser foot lever.
d
Release the presser foot locking pin (black button).
The presser foot remains level, allowing the fabric to
be fed.
After the seam is sewn, the presser foot will return to
its original angle.
■
Sewing thin fabrics
When sewing thin fabrics such as chiffon, the stitching
may become misaligned or the fabric may not feed
correctly. Move the needle (be sure to use a fine needle) to
the furthest left or right hand position so that the fabric
does not get pulled down into the feed dog area. If this
occurs or there is shrinkage of the stitching, place non-
woven water-soluble stabilizer under the fabric and sew
them together.
1
Presser foot
locking pin (black
button)
b
a
d
c
a
Memo
•
You may find adjusting the [Presser Foot Pressure]
in the settings screen helpful on some thick fabrics.
CAUTION
•
Do not sew fabric more than 6 mm (15/64
inch) thick or forcefully push fabric.
Otherwise, the needle may break, possibly
resulting in injury.
1
Water-soluble stabilizer
(non-woven)
1