HP D5970A HP Netserver LXr 8000 to LXr 8500 Upgrade Guide - Page 15

Preparing for the Upgrade

Get HP D5970A - NetServer - LCII PDF manuals and user guides View all HP D5970A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

2 Preparing for the Upgrade This chapter explains the steps to take before you begin the upgrade. l Gather the tools you need. l Back up your data. l Check the internal event log. l Set up your work area. l Open the boxes and verify their contents. Tools You Need To install this accessory you need the following tools: • An anti-static service kit (3M™ 8501/8502/8503 or equivalent). This kit includes a static-dissipating work surface, a chassis clip lead, and a wrist strap. • Several anti-static mats • T15 Torx® screwdriver (slender enough to insert into the bezel hinge) If you need to remove the NetServer from a rack, you will also need some additional tools. Refer to the HP NetServer LXr 8500 Installation Guide and your rack documentation for further details. Back Up Your Data Before you start the upgrade, you must back up all hard disk drives and verify that the backup can be restored. CAUTION It is extremely important that you back up all data. After you complete the hardware upgrade, you will clear your boot drive and reinstall your NOS. If you have data stored on your boot drive, make a second complete backup of this data. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
9
2
Preparing for the Upgrade
This chapter explains the steps to take before you begin the upgrade.
Gather the tools you need.
Back up your data.
Check the internal event log.
Set up your work area.
Open the boxes and verify their contents.
Tools You Need
To install this accessory you need the following tools:
•
An anti-static service kit (3M
8501/8502/8503 or equivalent). This kit
includes a static-dissipating work surface, a chassis clip lead, and a wrist
strap.
•
Several anti-static mats
•
T15 Torx
®
screwdriver (slender enough to insert into the bezel hinge)
If you need to remove the NetServer from a rack, you will also need some
additional tools. Refer to the
HP NetServer LXr 8500 Installation Guide
and your
rack documentation for further details.
Back Up Your Data
Before you start the upgrade, you must back up all hard disk drives and verify that
the backup can be restored.
CAUTION
It is extremely important that you back up
all
data. After you
complete the hardware upgrade, you will clear your boot drive
and reinstall your NOS. If you have data stored on your boot
drive, make a second complete backup of this data.