HP D5970A HP Netserver LXr 8000 to LXr 8500 Upgrade Guide - Page 60

Install the Memory Board

Get HP D5970A - NetServer - LCII PDF manuals and user guides View all HP D5970A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Chapter 5 Install the Memory Board Assembling the LXr 8500 15a. Lift LCD handle up. 15b. Insert one or two memory boards (component-side down). 15c. Close memory board latches. Figure 5-14. Insert Memory Board 15. Insert the LXr 8500 memory board(s) into the chassis. (See Figure 5-14.) a. Lift the LCD handle up until it stops. b. Locate the memory board guides, and insert the board(s) with the component-side down. NOTE You must insert the memory boards into the board guides for them to engage correctly. If you are using only one memory board, it can be installed in either slot, left or right. There is no need for a terminator in the open memory board slot. c. Close the memory board latches by pressing them in toward the center of each board. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
Chapter 5
Assembling the LXr 8500
54
Install the Memory Board
15a. Lift LCD handle up.
15b. Insert one or two
memory boards
(component-side down).
15a. Lift LCD handle up.
15c. Close memory board latches.
Figure 5-14. Insert Memory Board
15.
Insert the LXr 8500 memory board(s) into the chassis. (See Figure 5-14.)
a.
Lift the LCD handle up until it stops.
b.
Locate the memory board guides, and insert the board(s) with the
component-side down.
NOTE
You must insert the memory boards into the board guides for
them to engage correctly.
If you are using only one memory board, it can be installed in either
slot, left or right. There is no need for a terminator in the open memory
board slot.
c.
Close the memory board latches by pressing them in toward the center
of each board.