HP D5970A HP Netserver LXr 8000 to LXr 8500 Upgrade Guide - Page 66

Apply one medium-length folded-foam gasket on the floor of each

Get HP D5970A - NetServer - LCII PDF manuals and user guides View all HP D5970A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Chapter 5 Assembling the LXr 8500 Open tabs of metal gaskets 24d. Center long gaskets on point to center of NetServer. top edge of each power supply bay. 24a. Place medium-length gasket about 1 inch (25mm) in from edge of chassis. 24b. Place "CAUTION" label behind gasket on floor of power supply bay. 24c. Place metal gaskets on both sides of each power supply bay. Figure 5-20. Apply Gaskets to All Three Power Supply Bays 24. Apply gaskets and "CAUTION" labels to each of the three power supply bays as follows (see Figure 5-20): a. Apply one medium-length folded-foam gasket on the floor of each power supply bay, approximately 1 inch (25mm) in from the edge of the chassis. b. Apply one "CAUTION" label behind each gasket on the floor of each power supply bay. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
Chapter 5
Assembling the LXr 8500
60
24d. Center long gaskets on
top edge of each power supply bay.
Open tabs of metal gaskets
point to center of NetServer.
24a. Place medium-length gasket about
1 inch (25mm) in from edge of chassis.
24b. Place “CAUTION” label behind
gasket on floor of power supply bay.
24c. Place metal gaskets on
both sides of each power supply bay.
Figure 5-20. Apply Gaskets to All Three Power Supply Bays
24.
Apply gaskets and "CAUTION" labels to each of the three power supply
bays as follows (see Figure 5-20):
a.
Apply one medium-length folded-foam gasket on the floor of each
power supply bay, approximately 1 inch (25mm) in from the edge of
the chassis.
b.
Apply one "CAUTION" label behind each gasket on the floor of each
power supply bay.