HP D5970A HP Netserver LXr 8000 to LXr 8500 Upgrade Guide - Page 39

Apply Gaskets to Chassis

Get HP D5970A - NetServer - LCII PDF manuals and user guides View all HP D5970A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Chapter 3 Disassembling the LXr 8000 Apply Gaskets to Chassis 32. Remove adhesive strip covering from 2 short folded foam gaskets and apply to bottom corners of chassis. 31. Remove 4 screws and slide out peripheral bay. 33. Reinsert the peripheral bay and secure all 4 screws. Figure 3-14. Remove Peripheral Bay and Apply Foam Gaskets 31. Remove the four screws that secure the peripheral bay to the chassis and slide out the peripheral bay. (See Figure 3-14.) NOTE Sheet metal surfaces must be free of oil, grease, and other foreign material to ensure good adhesion of gaskets. Clean the chassis with alcohol or other fluid as necessary. 32. Locate the two short folded foam gaskets that are approximately 1 inch in length. Remove the adhesive strip covering and apply the gaskets to the bottom of the chassis as shown in Figure 3-14. 33. Reinsert the peripheral bay and secure all four screws. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
Chapter 3
Disassembling the LXr 8000
33
Apply Gaskets to Chassis
31. Remove 4 screws and
slide out peripheral bay.
33. Reinsert the peripheral bay
and secure all 4 screws.
32. Remove adhesive strip covering from
2 short folded foam gaskets and apply
to bottom corners of chassis.
Figure 3-14. Remove Peripheral Bay and Apply Foam Gaskets
31.
Remove the four screws that secure the peripheral bay to the chassis and
slide out the peripheral bay. (See Figure 3-14.)
NOTE
Sheet metal surfaces must be free of oil, grease, and other
foreign material to ensure good adhesion of gaskets. Clean the
chassis with alcohol or other fluid as necessary.
32.
Locate the two short folded foam gaskets that are approximately 1 inch in
length. Remove the adhesive strip covering and apply the gaskets to the
bottom of the chassis as shown in Figure 3-14.
33.
Reinsert the peripheral bay and secure all four screws.