HP D5970A HP Netserver LXr 8000 to LXr 8500 Upgrade Guide - Page 77

Install Accessory Boards in the I/O Baseboard

Get HP D5970A - NetServer - LCII PDF manuals and user guides View all HP D5970A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Chapter 7 NOTE Finishing the Assembly 5V and 3.3V PCI boards are keyed such that it is not possible to insert them into the wrong voltage slots. Universal boards are keyed such that they can be placed in any slot. Refer to the HP NetServer LXr 8500 Installation Guide for more complete information on adding accessory boards. Install Accessory Boards in the I/O Baseboard 5. Install each accessory board in the I/O tray as follows: 5a. Press the center of the PCI hold-down latch to disengage it. Then swing it back out of the way. Figure 7-1. PCI Hold-down Latch a. Release the PCI hold-down latch to open the slot. (See Figure 7-1.) The PCI hold-down latch is used to keep the PCI boards in place and to activate the PCI LED display. The PCI LED display indicates if power is applied to the individual slot, or if the slot has a problem, such as a cable is disconnected from the board. 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
Chapter 7
Finishing the Assembly
71
NOTE
5V and 3.3V PCI boards are keyed such that it is not possible
to insert them into the wrong voltage slots. Universal boards
are keyed such that they can be placed in any slot.
Refer to the
HP NetServer LXr 8500 Installation Guide
for
more complete information on adding accessory boards.
Install Accessory Boards in the I/O Baseboard
5.
Install each accessory board in the I/O tray as follows:
5a. Press the center of the
PCI hold-down latch to
disengage it. Then swing
it back out of the way.
Figure 7-1. PCI Hold-down Latch
a.
Release the PCI hold-down latch to open the slot. (See Figure 7-1.)
The PCI hold-down latch is used to keep the PCI boards in place and to
activate the PCI LED display. The PCI LED display indicates if power
is applied to the individual slot, or if the slot has a problem, such as a
cable is disconnected from the board.