Compaq ProLiant 1600 Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenanc - Page 112

Message, Description, Recommended Action, Run Options ROMPaq - drive location

Get Compaq ProLiant 1600 PDF manuals and user guides View all Compaq ProLiant 1600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

3-58 Diagnostic Tools DAAD Diagnostic Messages Continued Message Description Configuration Array accelerator board signature configured for a different array mismatch controller board. Configuration signature on array accelerator board does not match the one stored on the array controller board. Controller Controller communication communication failure occurred. failure occurred Controller detected. NVRAM configuration not present Controller firmware needs upgrading Controller firmware needs upgrading (DAAD Error 102) Controller is located in special " video" slot Controller is not configured EISA nonvolatile RAM does not contain a configuration for this controller. Controller firmware is below the latest recommended version. Controller is correct, however, IDA firmware version should be greater than 1.26. Controller is installed in slot for special video control signals. If controller is used in this slot, LED indicators on front panel may not function properly. Controller is not configured. If controller was previously configured and you change drive locations, there may be a problem with placement of the drives. DAAD examines each physical drive and looks for drives that have been moved to a different drive bay. Controller needs replacing (DAAD Error 102) IDA firmware is less than version 0.96. Recommended Action To recognize the array accelerator board, run the System Configuration Utility. DAAD was unable to successfully issue commands to the controller in this slot. Run the System Configuration Utility to configure the nonvolatile RAM. Run Options ROMPaq to upgrade the controller to the latest firmware revision. Obtain the latest firmware. Install the controller in a different slot and run the System Configuration Utility to configure the controller and nonvolatile RAM. Look for messages indicating which drives have been moved. If none appear and drive swapping did not occur, run the System Configuration Utility to configure the controller and nonvolatile RAM. Do not run the System Configuration Utility if you believe drive swapping has occurred. Replace the controller as soon as possible.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3-58
Diagnostic Tools
DAAD Diagnostic Messages
Continued
Message
Description
Recommended Action
Configuration
signature
mismatch
Array accelerator board
configured for a different array
controller board.
Configuration signature on
array accelerator board does
not match the one stored on
the array controller board.
To recognize the array
accelerator board, run the
System Configuration Utility.
Controller
communication
failure occurred
Controller communication
failure occurred.
DAAD was unable to
successfully issue
commands to the
controller in this slot.
Controller
detected. NVRAM
configuration not
present
EISA nonvolatile RAM does not
contain a configuration for this
controller.
Run the System
Configuration Utility to
configure the nonvolatile
RAM.
Controller firmware
needs upgrading
Controller firmware is below
the latest recommended
version.
Run Options ROMPaq to
upgrade the controller to
the latest firmware revision.
Controller firmware
needs upgrading
(DAAD Error 102)
Controller is correct, however,
IDA firmware version should be
greater than 1.26.
Obtain the latest firmware.
Controller is
located in special
“video” slot
Controller is installed in slot for
special video control signals. If
controller is used in this slot,
LED indicators on front panel
may not function properly.
Install the controller in a
different slot and run the
System Configuration Utility
to configure the controller
and nonvolatile RAM.
Controller is not
configured
Controller is not configured. If
controller was previously
configured and you change
drive locations, there may be
a problem with placement of
the drives. DAAD examines
each physical drive and looks
for drives that have been
moved to a different drive
bay.
Look for messages
indicating which drives
have been moved. If none
appear and drive
swapping did not occur,
run the System
Configuration Utility to
configure the controller
and nonvolatile RAM.
Do
not
run the System
Configuration Utility if you
believe drive swapping has
occurred.
Controller needs
replacing (DAAD
Error 102)
IDA firmware is less than
version 0.96.
Replace the controller as
soon as possible.