Compaq ProLiant 1600 Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenanc - Page 120

DRIVE REPLACED, will occur.

Get Compaq ProLiant 1600 PDF manuals and user guides View all Compaq ProLiant 1600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 120 highlights

3-66 Diagnostic Tools DAAD Diagnostic Messages Continued Message Description Logical Drive X A physical drive in this logical status = WRONG drive has failed. The incorrect DRIVE REPLACED drive was replaced. Loose cable detected - logical drives may be marked FAILED until corrected Mirror data miscompare Mirrored memory location errors No configuration for Accelerator Board Controller unable to communicate with one or more physical drives, probably because of a cabling problem. Logical drives may be in a FAILED state until the condition is corrected, preventing access to data on the controller. Data was found at reinitialization in the posted write memory; however, the mirror data compare test failed resulting in data being marked as invalid. Data loss is possible. Soft errors occurred when attempting to read the same data from both sides of the mirrored memory. Data loss will occur. The array accelerator board has not been configured. Drive (bay) X has loose cable The array controller could not communicate with this drive at power-up. This drive has not previously failed. Recommended Action Replace the drive that was incorrectly replaced. Then, replace the original drive that failed with a new drive. Do not run the System Configuration Utility to reconfigure; you will lose data on the drive. Check all controller and drive cable connections. Replace the array accelerator board. Replace the array accelerator board. If the array accelerator board is present, run the System Configuration Utility to configure the board, if desired. Check all cable connections first. The cables could be bad, loose, or disconnected. Turn on the system and attempt to reconnect data/power cable to the drive. If this does not work, replace the

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3-66
Diagnostic Tools
DAAD Diagnostic Messages
Continued
Message
Description
Recommended Action
Logical Drive X
status = WRONG
DRIVE REPLACED
A physical drive in this logical
drive has failed. The incorrect
drive was replaced.
Replace the drive that was
incorrectly replaced. Then,
replace the original drive
that failed with a new drive.
Do not run the System
Configuration Utility to
reconfigure; you will lose
data on the drive.
Loose cable
detected - logical
drives may be
marked FAILED
until corrected
Controller unable to
communicate with one or
more physical drives, probably
because of a cabling
problem. Logical drives may
be in a FAILED state until the
condition is corrected,
preventing access to data on
the controller.
Check all controller and
drive cable connections.
Mirror data
miscompare
Data was found at
reinitialization in the posted
write memory; however, the
mirror data compare test
failed resulting in data being
marked as invalid. Data loss is
possible.
Replace the array
accelerator board.
Mirrored memory
location errors
Soft errors occurred when
attempting to read the same
data from both sides of the
mirrored memory. Data loss
will occur.
Replace the array
accelerator board.
No configuration
for Accelerator
Board
The array accelerator board
has not been configured.
If the array accelerator
board is present, run the
System Configuration Utility
to configure the board, if
desired.
Drive (bay) X has
loose cable
The array controller could not
communicate with this drive
at power-up. This drive has not
previously failed.
Check all cable
connections first. The cables
could be bad, loose, or
disconnected. Turn on the
system and attempt to
reconnect data/power
cable to the drive. If this
does not work, replace the