Compaq ProLiant 1600 Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenanc - Page 122

Run Options ROMPaq to, Upgrade Utility. However,

Get Compaq ProLiant 1600 PDF manuals and user guides View all Compaq ProLiant 1600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 122 highlights

3-68 Diagnostic Tools DAAD Diagnostic Messages Continued Message Description Drive (bay) X is a This drive has been replaced replacement drive and marked OK by the marked OK firmware. This may occur if a drive has an intermittent failure (for example, if a drive has previously failed, then when DAAD is run, the drive starts working again). Drive (bay) X is The indicated physical drive failed has failed. Drive (bay) X has Drive has insufficient capacity insufficient to be used in this logical drive capacity for its configuration. configuration Drive (bay) X is This drive is being rebuilt from undergoing drive the corresponding mirror or recovery parity data. Drive (bay) X was The physical drive was inadvertently incorrectly replaced after replaced another drive failed. SCSI port X, drive ID Y firmware needs upgrading Set configuration command issued Soft Firmware Upgrade required Drive's firmware may cause problems and should be upgraded. The configuration of the array controller has been updated. The array accelerator board may remain disabled until it is reinitialized. DAAD has determined that your controller is running firmware that has been soft upgraded by the Compaq Upgrade Utility. However, the firmware running is not present on all drives. This could be caused by the addition of new drives in the system. Recommended Action Replace the drive. Replace this drive. Replace this drive with a larger capacity drive. Normal operations should occur. Replace the drive that was incorrectly replaced and replace the original drive that failed. Do not run the System Configuration Utility and try to reconfigure; data will be lost. Run Options ROMPaq to upgrade the drive's firmware to a later revision. Run the System Configuration Utility to reinitialize the array accelerator board. Run the Compaq Upgrade Utility to place the latest firmware on all drives.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3-68
Diagnostic Tools
DAAD Diagnostic Messages
Continued
Message
Description
Recommended Action
Drive (bay) X is a
replacement drive
marked OK
This drive has been replaced
and marked OK by the
firmware. This may occur if a
drive has an intermittent
failure (for example, if a drive
has previously failed, then
when DAAD is run, the drive
starts working again).
Replace the drive.
Drive (bay) X is
failed
The indicated physical drive
has failed.
Replace this drive.
Drive (bay) X has
insufficient
capacity for its
configuration
Drive has insufficient capacity
to be used in this logical drive
configuration.
Replace this drive with a
larger capacity drive.
Drive (bay) X is
undergoing drive
recovery
This drive is being rebuilt from
the corresponding mirror or
parity data.
Normal operations should
occur.
Drive (bay) X was
inadvertently
replaced
The physical drive was
incorrectly replaced after
another drive failed.
Replace the drive that was
incorrectly replaced and
replace the original drive
that failed. Do not run the
System Configuration Utility
and try to reconfigure; data
will be lost.
SCSI port X, drive
ID Y firmware
needs upgrading
Drive’s firmware may cause
problems and should be
upgraded.
Run Options ROMPaq to
upgrade the drive’s
firmware to a later revision.
Set configuration
command issued
The configuration of the array
controller has been updated.
The array accelerator board
may remain disabled until it is
reinitialized.
Run the System
Configuration Utility to
reinitialize the array
accelerator board.
Soft Firmware
Upgrade required
DAAD has determined that
your controller is running
firmware that has been soft
upgraded by the Compaq
Upgrade Utility. However, the
firmware running is not
present on all drives. This
could be caused by the
addition of new drives in the
system.
Run the Compaq Upgrade
Utility to place the latest
firmware on all drives.