Compaq ProLiant 8500 ProLiant 8500 Servers Maintenance and Service Guide - Page 27

Weight Warning, Rack Warnings, Compaq ProLiant 8500 Setup, and Installation Guide

Get Compaq ProLiant 8500 PDF manuals and user guides View all Compaq ProLiant 8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

2-4 Compaq ProLiant 8500 Server Maintenance and Service Guide Before beginning any of the removal and replacement procedures for non-hot-pluggable devices: 1. Press the Power On/Standby switch to Standby. This places the server in Standby mode, thereby disabling the main power supply output and providing auxiliary power (+5V) to the server. Standby does not disable main input power. 2. Verify that the system LED on the front panel, near the Power On/Standby switch, is off and that the fan noise stops. 3. Disconnect all power cords from the server to disable all power to the server. 4. For some removal and replacement procedures, you must remove the server from the rack and place it on a sturdy table or workbench. Refer to the Compaq ProLiant 8500 Setup and Installation Guide for instructions. Weight Warning 42-62 kg 93-137 lb WARNING The Compaq ProLiant 8500 weighs 62 kilograms (137 pounds) when fully assembled. To reduce the risk of personal injury or damage to the equipment: I Observe local health and safety requirements and guidelines for manual material handling. I Obtain adequate assistance to lift and stabilize the product during installation or removal. I Remove all pluggable modules and power supplies to reduce the overall weight of the product. Rack Warnings WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: I The leveling jacks are extended to the floor. I The full weight of the rack rests on the leveling jacks. I The stabilizers are attached to the rack if it is a single-rack installation. I The racks are coupled together in multiple-rack installations. I Only one component is extended at a time. A rack may become unstable if more than one component is extended for any reason.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
2-4
Compaq ProLiant 8500 Server Maintenance and Service Guide
Before beginning any of the removal and replacement procedures for non-hot-pluggable
devices:
1.
Press the Power On/Standby switch to Standby. This places the server in Standby mode,
thereby disabling the main power supply output and providing auxiliary power (+5V) to
the server. Standby does not disable main input power.
2.
Verify that the system LED on the front panel, near the Power On/Standby switch, is off
and that the fan noise stops.
3.
Disconnect all power cords from the server to disable all power to the server.
4.
For some removal and replacement procedures, you must remove the server from the rack
and place it on a sturdy table or workbench. Refer to the
Compaq ProLiant 8500 Setup
and Installation Guide
for instructions.
Weight Warning
42-62 kg
93-137 lb
WARNING
The Compaq ProLiant 8500 weighs 62 kilograms (137 pounds) when fully
assembled. To reduce the risk of personal injury or damage to the equipment:
■
Observe local health and safety requirements and guidelines for manual material
handling.
■
Obtain adequate assistance to lift and stabilize the product during installation or
removal.
■
Remove all pluggable modules and power supplies to reduce the overall weight of
the product.
Rack Warnings
WARNING:
To reduce the risk of personal injury or damage to the equipment, be sure that:
■
The leveling jacks are extended to the floor.
■
The full weight of the rack rests on the leveling jacks.
■
The stabilizers are attached to the rack if it is a single-rack installation.
■
The racks are coupled together in multiple-rack installations.
■
Only one component is extended at a time. A rack may become unstable if more than one
component is extended for any reason.