Compaq ProLiant 8500 ProLiant 8500 Servers Maintenance and Service Guide - Page 76

Power On/Standby Switch Assembly, To remove the Power On/Standby switch

Get Compaq ProLiant 8500 PDF manuals and user guides View all Compaq ProLiant 8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Removal and Replacement Procedures 2-53 Power On/Standby Switch Assembly To remove the Power On/Standby switch: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the media module bezel. See "Media Module Bezel" earlier in this chapter. 3. Remove the media module. See "Media Module" earlier in this chapter. 4. Unplug the IMD cable from the media backplane board. See "Media Module Cable Routing Diagram" earlier in this chapter. 5. Remove the IMD. See "Integrated Management Display" earlier in this chapter.  6. Disconnect the Power On/Standby switch connector from the media backplane board . See "Media Module Cable Routing Diagram" earlier in this chapter. 7. Loosen the thumbscrew that secures the power switch plate to the media backplane board . 2 1 Figure 2-46. Unplugging the power switch cable and loosening the thumbscrew

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
Removal and Replacement Procedures
2-53
Power On/Standby Switch Assembly
To remove the Power On/Standby switch:
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the media module bezel. See
“
Media Module Bezel
”
earlier in this chapter.
3.
Remove the media module. See
“
Media Module
”
earlier in this chapter.
4.
Unplug the IMD cable from the media backplane board. See
“
Media Module Cable
Routing Diagram
”
earlier in this chapter.
5.
Remove the IMD. See
“
Integrated Management Display
”
earlier in this chapter.
6.
Disconnect the Power On/Standby switch connector from the media backplane board
.
See
“
Media Module Cable Routing Diagram
”
earlier in this chapter.
7.
Loosen the thumbscrew that secures the power switch plate to the media backplane
board
.
1
2
Figure 2-46.
Unplugging the power switch cable and loosening the thumbscrew