Compaq ProLiant 8500 ProLiant 8500 Servers Maintenance and Service Guide - Page 50

Processor, Opening and Removing the Processor

Get Compaq ProLiant 8500 PDF manuals and user guides View all Compaq ProLiant 8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Removal and Replacement Procedures 2-27 Processor CAUTION: Handle the processor only by the ejectors. If you must set the processor down, lay it down on the side with the hologram to prevent damage to the heat pipes and fins. IMPORTANT: If you remove a processor, a processor terminator board must be reinstalled in the slot before powering up the server. To remove a processor: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the processor and memory module. See "Opening and Removing the Processor and Memory Module" earlier in this chapter. 3. Rotate the front and rear ejector levers on the processor outward until the processor is  disconnected from the connector .  4. Remove the processor by lifting up on the ejectors . 1 1 2 Figure 2-20. Removing a processor Reverse steps 1 through 4 to replace a processor.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
Removal and Replacement Procedures
2-27
Processor
CAUTION:
Handle the processor only by the ejectors. If you must set the processor down, lay it
down on the side with the hologram to prevent damage to the heat pipes and fins.
IMPORTANT:
If you remove a processor, a processor terminator board must be reinstalled in the slot
before powering up the server.
To remove a processor:
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the processor and memory module. See
“
Opening and Removing the Processor
and Memory Module
”
earlier in this chapter.
3.
Rotate the front and rear ejector levers on the processor outward until the processor is
disconnected from the connector
.
4.
Remove the processor by lifting up on the ejectors
.
2
1
1
Figure 2-20.
Removing a processor
Reverse steps 1 through 4 to replace a processor.