D-Link DES-3026 Reference Manual - Page 120

Port Mirroring Commands, config mirror port

Get D-Link DES-3026 - Switch PDF manuals and user guides
UPC - 790069280771
View all D-Link DES-3026 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 120 highlights

DES-3000 Series Layer 2 Switch CLI Reference Manual 15 PORT MIRRORING COMMANDS The port mirroring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config mirror port | [add | delete] source ports [rx | tx | both] enable mirror disable mirror show mirror Each command is listed, in detail, in the following sections. config mirror port Purpose Used to configure a mirror port − source port pair on the Switch. Syntax Description Parameters config mirror port | [add | delete] source ports [rx | tx | both] This command allows a range of ports to have all of their traffic also sent to a designated port, where a network sniffer or other device can monitor the network traffic. In addition, the user can specify that only traffic received by or sent by one or both is mirrored to the Target port. port − This specifies the Target port (the port where mirrored packets will be sent). [add | delete] - Specify whether to add or delete source ports, which will be specified using the following parameter. source ports - The port or ports being mirrored. This cannot include the Target port. − This specifies a range of ports that will be mirrored. That is, the range of ports in which all traffic will be copied and sent to the Target port. rx − Allows the mirroring of only packets received by (flowing into) the port or ports in the port list. rx - Allows the mirroring of only packets sent from (flowing from) the port or ports in the port list. tx − Allows the mirroring of only packets sent to (flowing out of) the port or ports in the port list. Restrictions both − Mirrors all the packets received or sent by the port or ports in the port list. The Target port cannot be listed as a source port. Only administratorlevel users can issue this command. Example usage: To configure the mirror ports: DES-3026:4# config mirror port 10 add source ports 1-5 both Command: config mirror port 10 add source ports 1-5 both Success. DES-3026:4# 116

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
DES-3000 Series Layer 2 Switch CLI Reference Manual
15
P
ORT
M
IRRORING
C
OMMANDS
The port mirroring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table.
Command
Parameters
config mirror
port <port> | [add | delete] source ports <portlist> [rx | tx | both]
enable mirror
disable mirror
show mirror
Each command is listed, in detail, in the following sections.
config mirror port
Purpose
Used to configure a mirror port
−
source port pair on the Switch.
Syntax
config mirror port <port> | [add | delete] source ports <portlist> [rx
| tx | both]
Description
This command allows a range of ports to have all of their traffic also
sent to a designated port, where a network sniffer or other device can
monitor the network traffic. In addition, the user can specify that only
traffic received by or sent by one or both is mirrored to the Target port.
Parameters
port <port>
−
This specifies the Target port (the port where mirrored
packets will be sent).
[add | delete] –
Specify whether to add or delete source ports, which will
be specified using the following parameter.
source ports
– The port or ports being mirrored. This cannot include the
Target port.
±
<portlist>
−
This specifies a range of ports that will be mirrored.
That is, the range of ports in which all traffic will be copied and sent
to the Target port.
rx
−
Allows the mirroring of only packets
received by (flowing into) the port or ports in the port list.
rx - Allows the mirroring of only packets sent from (flowing from) the
port or ports in the port list.
tx
−
Allows the mirroring of only packets sent to (flowing out of) the port
or ports in the port list.
both
−
Mirrors all the packets received or sent by the port or ports in the
port list.
Restrictions
The Target port cannot be listed as a source port. Only administrator-
level users can issue this command.
Example usage:
To configure the mirror ports:
DES-3026:4# config mirror port 10 add source ports 1-5 both
Command: config mirror port 10 add source ports 1-5 both
Success.
DES-3026:4#
116