D-Link DES-3026 Reference Manual - Page 128

config link_aggregation, ports <portlist> | state [enable | disable]} - d link manual

Get D-Link DES-3026 - Switch PDF manuals and user guides
UPC - 790069280771
View all D-Link DES-3026 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 128 highlights

Example usage: DES-3000 Series Layer 2 Switch CLI Reference Manual To delete link aggregation group: DES-3026:4#delete link_aggregation group_id 1 Command: delete link_aggregation group_id 1 Success. DES-3026:4# config link_aggregation Purpose Used to configure a previously created link aggregation group. Syntax config link_aggregation group_id {master_port | ports | state [enable | disable]} Description This command allows configuration of a link aggregation group that was created with the create link_aggregation command above. Parameters − Specifies the group ID. The Switch allows up to 3 link aggregation groups to be configured. The group number identifies each of the groups. group_id 3 is designed for the uplink modules only (the last two ports on the Switch (9-10, 17-18, 25-26) and can only be configured for them. master port − Master port ID. Specifies which port (by port number) of the link aggregation group will be the master port. All of the ports in a link aggregation group will share the port configuration with the master port. ports − Specifies a port or range of ports that will belong to the link aggregation group. Ports may be listed in only one port aggregation group, that is, link aggregation groups may not overlap. state [enable | disable] − Allows the user to enable or disable the specified link aggregation group. Restrictions Only administrator-level users can issue this command. Link aggregation groups may not overlap and must be contained on a single switch. Example usage: To define a load-sharing group of ports, group-id 1,master port 5 of module 1 with group members ports 5-7 plus port 9: DES-3026:4#config link_aggregation group_id 1 master_port 5 ports 5-7,9 Command: config link_aggregation group_id 1 master_port 5 ports 5-7,9 Success. DES-3026:4# NOTE: group_id 3 is designed for the uplink modules only (the last two ports on the Switch (DES-3010F/FL/G ports 9-10, DES-3018 ports 17-18, DES-3026 ports 25-26) and can only be configured for them. Any other attempt at configuring group_id 3 with standard 10/100 Mbps ports will result in a configuration error. 124

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
DES-3000 Series Layer 2 Switch CLI Reference Manual
Example usage:
To delete link aggregation group:
DES-3026:4#delete link_aggregation group_id 1
Command: delete link_aggregation group_id 1
Success.
DES-3026:4#
config link_aggregation
Purpose
Used to configure a previously created link aggregation group.
Syntax
config link_aggregation group_id <value 1-3> {master_port <port> |
ports <portlist> | state [enable | disable]}
Description
This command allows configuration of a link aggregation group that was
created with the
create link_aggregation
command above.
Parameters
<value 1-3>
−
Specifies the group ID. The Switch allows up to 3 link
aggregation groups to be configured. The group number identifies each of
the groups.
group_id 3
is designed for the uplink modules only (the last two
ports on the Switch (9-10, 17-18, 25-26) and can only be configured for
them.
master port <port>
−
Master port ID. Specifies which port (by port number)
of the link aggregation group will be the master port. All of the ports in a link
aggregation group will share the port configuration with the master port.
ports <portlist>
−
Specifies a port or range of ports that will belong to the
link aggregation group. Ports may be listed in only one port aggregation
group, that is, link aggregation groups may not overlap.
state [enable | disable]
−
Allows the user to enable or disable the specified
link aggregation group.
Restrictions
Only administrator-level users can issue this command. Link aggregation
groups may not overlap and must be contained on a single switch.
Example usage:
To define a load-sharing group of ports, group-id 1,master port 5 of module 1 with group members ports 5-7 plus port
9:
DES-3026:4#config link_aggregation group_id 1 master_port 5 ports 5-7,9
Command: config link_aggregation group_id 1 master_port 5 ports 5-7,9
Success.
DES-3026:4#
NOTE:
group_id 3
is designed for the uplink modules only (the last two ports on the
Switch (DES-3010F/FL/G ports 9-10, DES-3018 ports 17-18, DES-3026 ports 25-26) and
can only be configured for them. Any other attempt at configuring group_id 3 with
standard 10/100 Mbps ports will result in a configuration error.
124