D-Link DES-3026 Reference Manual - Page 202

DES-3000 Series Layer 2 Switch CLI Reference Manual, enable sim - user guide

Get D-Link DES-3026 - Switch PDF manuals and user guides
UPC - 790069280771
View all D-Link DES-3026 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 202 highlights

DES-3000 Series Layer 2 Switch CLI Reference Manual After configuring one switch to operate as the CS of a SIM group, additional switches may join the group by manually configuring the Switch to be a MS. The CS will then serve as the in band entry point for access to the MS. The CS's IP address will become the path to all MS's of the group and the CS's Administrator's password, and/or authentication will control access to all MS's of the SIM group. With SIM enabled, the applications in the CS will redirect the packet instead of executing the packets. The applications will decode the packet from the administrator, modify some data, then send it to the MS. After execution, the CS may receive a response packet from the MS, which it will encode and send it back to the administrator. When a CaS becomes a MS, it automatically becomes a member of the first SNMP community (include read/write and read only) to which the CS belongs. However if a MS has its own IP address, it can belong to SNMP communities to which other switches in the group, including the CS, do not belong. To join an SIM group, first enable the Switch for SIM using the enable sim command. Once enabled the switch is ready to join an SIM group yet to be a part of that group, the commander switch must be configured to accept the DES-3026 as a member switch. For more information on adding the DES-3026 as a member of an SIM group, please see the commander switch's user guide or command line interface reference manual. The D-Link Single IP Management commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command enable sim disable sim show sim reconfig config sim_group config sim download sim_ms upload sim_ms configuration Parameters {[candidates {} | members {} | group {commander_mac } | neighbor]} [member_id | exit] [add {} | delete ] [[commander {group_name } | candidate] | dp_interval | hold_time ] [firmware_from_tftp | configuration_from_tftp] {[members | all]} [configuration_to_tftp | log_to_tftp ] {members | all} Each command is listed, in detail, in the following sections. 198

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
DES-3000 Series Layer 2 Switch CLI Reference Manual
After configuring one switch to operate as the CS of a SIM group, additional switches may join the group by manually
configuring the Switch to be a MS. The CS will then serve as the in band entry point for access to the MS. The CS’s IP address
will become the path to all MS’s of the group and the CS’s Administrator’s password, and/or authentication will control access
to all MS’s of the SIM group.
With SIM enabled, the applications in the CS will redirect the packet instead of executing the packets. The applications will
decode the packet from the administrator, modify some data, then send it to the MS. After execution, the CS may receive a
response packet from the MS, which it will encode and send it back to the administrator.
When a CaS becomes a MS, it automatically becomes a member of the first SNMP community (include read/write and read
only) to which the CS belongs. However if a MS has its own IP address, it can belong to SNMP communities to which other
switches in the group, including the CS, do not belong.
To join an SIM group, first enable the Switch for SIM using the
enable sim
command. Once enabled the switch is ready to join
an SIM group yet to be a part of that group, the commander switch must be configured to accept the DES-3026 as a member
switch. For more information on adding the DES-3026 as a member of an SIM group, please see the commander switch’s user
guide or command line interface reference manual.
The D-Link Single IP Management commands in the Command Line Interface (CLI) are listed (along with the appropriate
parameters) in the following table.
Command
Parameters
enable sim
disable sim
show sim
{[candidates {<candidate_id 1-100>} | members {<member_id
1-32>} | group {commander_mac <macaddr>} | neighbor]}
reconfig
[member_id <value 1-32> | exit]
config sim_group
[add <candidate_id 1-100> {<password>} | delete
<member_id 1-32>]
config sim
[[commander {group_name <groupname 64>} | candidate] |
dp_interval <sec 30-90> | hold_time <sec 100-255>]
download sim_ms
[firmware_from_tftp | configuration_from_tftp] <ipaddr>
<path_filename> {[members <mslist 1-32> | all]}
upload sim_ms
configuration
[configuration_to_tftp | log_to_tftp ] <ipaddr> <path_filename>
{members <mslist> | all}
Each command is listed, in detail, in the following sections.
198