Dell Latitude D610 User Guide - Page 85

Changing Printer Modes, Changing COM Ports, Enabling the Infrared Sensor - system restore

Get Dell Latitude D610 PDF manuals and user guides View all Dell Latitude D610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

l Diskette Drive l Modular Bay HDD l Internal HDD l CD/DVD/CD-RW Drive During the boot routine, the computer starts at the top of the list and scans each enabled device for the operating system start-up files. When the computer finds the files, it stops searching and starts the operating system. To control the boot devices, select (highlight) a device by pressing the down-arrow or up-arrow key, and then enable or disable the device or change its order in the list. l To enable or disable a device, highlight the item and press the space bar. Enabled items appear as white and display a small triangle to the left; disabled items appear blue or dimmed without a triangle. l To reorder a device in the list, highlight the device and then press or (not case-sensitive) to move the highlighted device up or down. Boot sequence changes take effect as soon as you save the changes and exit system setup. Performing a One-Time Boot You can set a one-time-only boot sequence without entering system setup. (You can also use this procedure to boot the Dell Diagnostics on the diagnostics utility partition on your hard drive.) 1. Shut down the computer through the Start menu. 2. If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions. 3. Connect the computer to an electrical outlet. 4. Turn on the computer. When the DELL logo appears, press immediately. If you wait too long and the Windows logo appears, continue to wait until you see the Windows desktop. Then shut down your computer and try again. 5. When the boot device list appears, highlight the device from which you want to boot and press . The computer boots to the selected device. The next time you reboot the computer, the previous boot order is restored. Changing Printer Modes Set the Parallel Mode option according to the type of printer or device connected to the parallel connector. To determine the correct mode to use, see the documentation that came with the device. Setting Parallel Mode to Disabled disables the parallel port and the port's LPT address, which frees computer resources for another device to use. Changing COM Ports Serial Port allows you to map the serial port COM address or disable the serial port and its address, which frees computer resources for another device to use. Enabling the Infrared Sensor 1. Under Onboard Devices, select Fast IR. 2. Press to select the Fast IR setting, and use the right-arrow or left-arrow keys to change the setting to a COM port. NOTE: The default setting is Off. 3. Press and then to save the changes and exit the system setup program. After you enable the infrared sensor, you can use it to establish a link to an infrared device. To set up and use an infrared device, see the infrared device documentation and the Windows Help and Support Center. Back to Contents Page

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
l
Diskette Drive
l
Modular Bay HDD
l
Internal HDD
l
CD/DVD/CD-RW Drive
During the boot routine, the computer starts at the top of the list and scans each enabled device for the operating system start-up files. When the computer
finds the files, it stops searching and starts the operating system.
To control the boot devices, select (highlight) a device by pressing the down-arrow or up-arrow key, and then enable or disable the device or change its order
in the list.
l
To enable or disable a device, highlight the item and press the space bar. Enabled items appear as white and display a small triangle to the left;
disabled items appear blue or dimmed without a triangle.
l
To reorder a device in the list, highlight the device and then press <u> or <d> (not case-sensitive) to move the highlighted device up or down.
Boot sequence changes take effect as soon as you save the changes and exit system setup.
Performing a One-Time Boot
You can set a one-time-only boot sequence without entering system setup. (You can also use this procedure to boot the Dell Diagnostics on the diagnostics
utility partition on your hard drive.)
1.
Shut down the computer through the
Start
menu.
2.
If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions.
3.
Connect the computer to an electrical outlet.
4.
Turn on the computer. When the DELL logo appears, press <F12> immediately. If you wait too long and the Windows logo appears, continue to wait
until you see the Windows desktop. Then shut down your computer and try again.
5.
When the boot device list appears, highlight the device from which you want to boot and press <Enter>.
The computer boots to the selected device.
The next time you reboot the computer, the previous boot order is restored.
Changing Printer Modes
Set the
Parallel Mode
option according to the type of printer or device connected to the parallel connector. To determine the correct mode to use, see the
documentation that came with the device.
Setting
Parallel Mode
to
Disabled
disables the parallel port and the port's LPT address, which frees computer resources for another device to use.
Changing COM Ports
Serial Port
allows you to map the serial port COM address or disable the serial port and its address, which frees computer resources for another device to
use.
Enabling the Infrared Sensor
1.
Under
Onboard Devices
, select
Fast IR
.
2.
Press <Enter> to select the
Fast IR
setting, and use the right-arrow or left-arrow keys to change the setting to a COM port.
3.
Press <Enter> and then <Esc> to save the changes and exit the system setup program.
After you enable the infrared sensor, you can use it to establish a link to an infrared device. To set up and use an infrared device, see the infrared device
documentation and the
Windows Help and Support Center
.
Back to Contents Page
NOTE:
The default setting is
Off
.