HP 8/80 Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J
HP 8/80 Manual
View all HP 8/80 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 8/80 manual content summary:
- HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 1
DRAFT: BROCADE CONFIDENTIAL 53-1001762-01 ® 30 March 2010 Converged Enhanced Ethernet Command Reference Supporting Fabric OS v6.4.0 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 2
or service offered or to be offered by Brocade. Brocade reserves the brocade.com/support/oscd. Brocade Communications Systems, Incorporated Corporate and Latin American Headquarters Brocade Communications Systems, Inc. 1745 Technology Drive San Port Authentication Added new commands for IGMP July 2009 March - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 3
xvii Chapter 1 CLI Basics In this chapter 1 Accessing the Brocade CEE Switch 1 CLI command modes 1 L2 ACL commands 3 Chapter 2 Configuration Management Commands copy 5 copy startup-config 6 delete 7 dir 8 disable 9 do 10 enable 11 end 12 erase flash 13 exec-timeout 14 Converged - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 4
show system 35 show tech-support 36 show users 37 show version 38 terminal length 39 terminal monitor 40 write erase 41 write memory 42 VLAN Commands fcf forward 43 interface vlan 44 show interface 45 show vlan 46 show vlan classifier 47 switchport 48 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 5
73 clear lldp statistics 74 debug lldp packet 75 description 76 hello 77 lldp dcbx-version 78 lldp disable 79 lldp fcoe-priority-bits 80 lldp profile 81 mode 82 multiplier 83 profile 84 protocol lldp 85 show debug lldp 86 show lldp interface 87 Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 6
95 clear lacp counters 96 debug lacp 97 lacp system-priority 99 lacp timeout 100 show lacp counter 101 show lacp-sys-id 102 show port-channel 103 Layer 2 System Commands mac-address-table 105 show mac-address-table 107 Layer 2 ACL commands clear counters access-list mac 109 deny (extended - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 7
clear spanning-tree counter 127 debug spanning-tree 128 error-disable-timeout enable 129 error-disable-timeout interval 130 forward-delay 131 hello-time 132 instance 133 max-age 134 max-hops 135 port-channel path-cost 136 protocol spanning-tree 137 region 138 revision 139 show spanning- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 8
167 ip igmp last-member-query-interval 168 ip igmp query-interval 169 ip igmp query-max-response-time 170 ip igmp snooping enable (global version 171 ip igmp snooping enable (VLAN version 172 ip igmp snooping fast-leave 173 ip igmp snooping mrouter 174 ip igmp snooping mrouter-timeout 175 ip - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 9
Authentication Commands clear dot1x statistics 215 clear dot1x statistics interface 216 dot1x authentication 217 dot1x enable 218 dot1x port-control 219 dot1x quiet-period 220 dot1x reauthenticate interface 221 dot1x reauthentication 222 dot1x reauthMax 223 dot1x timeout re-authperiod 224 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 10
x Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 11
DRAFT: BROCADE CONFIDENTIAL About This Document In this chapter •How this document is organized xi •Supported hardware and software xii •What's components: • Chapter 1, "CLI Basics" describes how to access the switch and the CEE CLI command modes. • Chapter 2, "Configuration Management Commands - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 12
Switch • Brocade VA-40FC • Brocade 48000 • Brocade DCX • Brocade DCX-4S Within this manual, any appearance of the term "Brocade FCoE hardware" is referring to: • Brocade 8000 • Brocade FCOE10-24 port blade Although many different software and hardware configurations are tested and supported - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 13
BROCADE command names Identifies the names of user-manipulated GUI elements Identifies keywords and in the narrative portions of this guide are presented in mixed lettercase: for . Command syntax conventions Command syntax in this manual follows these conventions: TABLE 1 Command syntax conventions - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 14
notices and statements are used in this manual. They are listed below in order you or cause damage to hardware, firmware, software, or data. DANGER A Brocade and Fibre Channel, see the technical glossaries on Brocade Connect. See "Brocade resources" on page xv for instructions on accessing Brocade - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 15
and are also bundled with the Fabric OS firmware. Other industry resources White papers, online demonstrations, and data sheets are available through the Brocade website at http://www.brocade.com/products/software.jhtml. • Best practice guides, white papers, data sheets, and other documentation is - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 16
DRAFT: BROCADE CONFIDENTIAL Getting technical help Contact your switch support supplier for hardware, firmware, and software support, including product repairs and part ordering. To expedite your call, have the following information available: 1. General Information • Switch model • Switch operating - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 17
an error or an omission, or you think that a topic needs further development, we want to hear from you. Forward your feedback to: [email protected] Provide the title and version number of the document and as much detail as possible about your comment, including the topic heading and page - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 18
DRAFT: BROCADE CONFIDENTIAL xviii Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 19
to enter a login name and password. When you log on to a switch supporting CEE, all of the 10 Gbps ports are disabled and must be enabled. Refer to the Fibre Channel over Ethernet Administrator's Guide for information regarding feature configuration and management procedures. Following is an example - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 20
modes DRAFT: BROCADE CONFIDENTIAL TABLE 2 Command mode EXEC Accessing the CEE CLI command modes Prompt switch> Privileged EXEC switch# Global switch(config)# configuration Interface Port-channel: configuration switch (conf-if-po-63)# 10-Gigabit Ethernet (CEE port): switch (conf-if - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 21
BROCADE CONFIDENTIAL L2 ACL commands 1 L2 ACL commands Use Layer 2 Media Access Control (MAC) list commands to do the following: • Identify traffic based protocols, TCP or UDP port numbers, type of service and to provide Reflective access-lists and Time-based access-lists.capabilities. Converged - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 22
1 L2 ACL commands DRAFT: BROCADE CONFIDENTIAL 4 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 23
DRAFT: BROCADE CONFIDENTIAL Configuration Management Commands Chapter 2 copy Synopsis to a remote machine using FTP: switch#copy ftp://[email protected]/file1 file2 Source password[]? To copy the source file from a remote machine using SCP: switch#copy scp://user:[email protected]/file1 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 24
2 copy startup-config DRAFT: BROCADE CONFIDENTIAL copy startup-config Synopsis Operands Copies the when using this command: • An error displays if there is no startup configuration file, for example: switch #copy startup-config file2 % Error: No Startup-config. • Use the write memory command to - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 25
DRAFT: BROCADE CONFIDENTIAL delete 2 delete Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Deletes a specified file from the Flash. delete filename filename Specifies the name of the file to be deleted from the Flash of the local switch using the - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 26
2 dir DRAFT: BROCADE CONFIDENTIAL dir Synopsis Operands Defaults Command Modes directory. There are no usage guidelines for this command. To list the contents of the current directory: switch#dir Contents of flash:// -rw-r-----rw-r-----rw-r-----rw-r----- 1276 1276 1276 1276 Wed Feb 4 07:08 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 27
DRAFT: BROCADE CONFIDENTIAL disable 2 disable Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See of returning to the EXEC mode. To return to the EXEC mode: switch#disable switch> enable, end, exit Converged Enhanced Ethernet Command Reference 9 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 28
2 do DRAFT: BROCADE CONFIDENTIAL do Synopsis Operands Defaults Command Modes Description Usage Guidelines -r-----rw-r-----rw-r-----rw-r----switch(config)# 1276 1276 1276 1276 Wed Feb 4 07:08:49 2009 Wed Feb 4 07:10:30 2009 Wed Feb 4 07:12:33 2009 Wed Feb 4 10:48:59 2009 startup_rmon_config - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 29
EXEC mode from Privileged EXEC mode, use the disable command. Using the exit or quit command from the Privileged EXEC mode ends the session. To enable the Privileged EXEC mode: switch> enable switch# disable Converged Enhanced Ethernet Command Reference 11 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 30
2 end DRAFT: BROCADE CONFIDENTIAL end Synopsis Operands Defaults Command Modes Description EXEC mode from interface configuration mode: switch(config)#interface tengigabitethernet 0/0 switch(conf-if-te-0/0)#end switch# exit, disable, enable 12 Converged Enhanced Ethernet Command Reference 53 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 31
DRAFT: BROCADE CONFIDENTIAL erase flash 2 erase flash Synopsis Operands Defaults Command Modes Description Usage no usage guidelines for this command. To erase the files from the Flash: switch#erase flash %% Warning: Erasing flash filesystem will remove all files in flash://. Continue to erase - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 32
BROCADE CONFIDENTIAL exec-timeout Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Sets the interval that the EXEC command interpreter wait for user : switch(config)#line console 0 switch(conf-line)#exec-timeout 2 30 switch(config)#line vty 0 9 switch(conf - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 33
DRAFT: BROCADE CONFIDENTIAL exit 2 exit Synopsis Operands Defaults Command Modes Description and return to the Configuration mode: switch(config)#interface tengigabitethernet 0/0 switch(conf-if-te-0/0)#exit switch(config)#exit end, enable, disable Converged Enhanced Ethernet Command Reference - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 34
2 fos DRAFT: BROCADE CONFIDENTIAL fos Synopsis Operands Defaults Command Modes Description Executes Fabric OS commands from the from the cmsh shell. fos command command Specifies the Fabric OS - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 35
switchName: switch switchType: 76.6 switchState: Online switchMode: Native switchRole: Principal switchDomain: 1 switchId: fffc01 switchWwn: 10:00:00:05:1e:76:42:00 zoning: OFF switchBeacon: OFF Area Port Media Speed State Proto 0 0 -- N8 No_Module FC 1 1 -- N8 No_Module FC - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 36
2 line console DRAFT: BROCADE CONFIDENTIAL line console Synopsis Operands Defaults Command Modes Description wait interval for the console session: switch>enable switch#configure terminal switch(config)#line console 0 switch(config-line)#exec-timeout 2 30 switch(config-line)#exit show line 18 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 37
DRAFT: BROCADE CONFIDENTIAL line vty 2 line vty Synopsis Operands Defaults Command after 2 minutes, 30 seconds if there is no response from the user: switch#configure terminal switch(config)#line vty 23 31 switch(conf-line)#exec-timeout 2 30 show line Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 38
2 pwd DRAFT: BROCADE CONFIDENTIAL pwd Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also are no usage guidelines for this command. To view the current working directory: switch#pwd flash: none 20 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 39
DRAFT: BROCADE CONFIDENTIAL rename 2 rename Synopsis Operands Defaults Command Modes Description There are no usage guidelines for this command. To rename a file in the Flash: switch#rename file1 file2 switch#dir Contents of flash:// -rw-r----- 1276 Wed Feb 4 13:16:00 2009 file2 none - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 40
2 show calendar DRAFT: BROCADE CONFIDENTIAL show calendar Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also View the current date and time based on the switch hardware clock. show calendar none There are no default configurations for this command. Privileged - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 41
DRAFT: BROCADE CONFIDENTIAL show clock 2 show clock Synopsis Operands Defaults Command Modes Description guidelines for this command. To display the time and date from the system clock: switch#show clock 23:45:55.512800 UTC Wed Feb 18 2009 show calendar Converged Enhanced Ethernet Command Reference - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 42
2 show environment DRAFT: BROCADE CONFIDENTIAL show environment Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays fan, temperature, redundant power system (RPS) availability, and power information for the switch. show environment none There are no - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 43
DRAFT: BROCADE CONFIDENTIAL show file 2 show file Synopsis Operands Defaults Command Modes command. To show the file system for internal flash: switch#show file flash://file1 ! protocol spanning-tree mstp instance 1 vlan 100 ! [or] switch#show file file1 ! protocol spanning-tree mstp instance 1 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 44
2 show line DRAFT: BROCADE CONFIDENTIAL show line Synopsis Operands Defaults Command Modes Timeout(m/s) 10:0 10:0 10:0 10:0 10:0 10:0 10:0 10:0 10:0 10:0 10:0 10:0 10:0 121:1212 switch#show line 0 Status Type Idle console 0 * Active vty 0 Timeout(m/s) 10:0 10:0 line vty, line console, exec - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 45
BROCADE CONFIDENTIAL show logging 2 show logging Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays the internal syslog buffer of the switch Interface TenGigabitEthernet 0/4 is online. Interface Port-channel 10 is link down none Converged Enhanced - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 46
BROCADE CONFIDENTIAL show media Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays the SFP information for all the interfaces present on a switch (Volts) Current 0.002 (mAmps) TX Power 0.1 (uWatts) RX Power 0.1 (uWatts) (output truncated) show - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 47
BROCADE CONFIDENTIAL show media interface 2 show media interface Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays the SFP information for a specific interface. show media interface tengigabitethernet slot port TX Power 0.1 (uWatts) RX Power - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 48
SFP information for line card number 0: switch#show media linecard 0 Interface TenGigabitEthernet units 10 meters) Length Cu 0 (units 1 meter) Vendor Name BROCADE Vendor OUI 42:52:4f Vendor PN 57-0000075-01 Vendor Rev 0.002 (mAmps) TX Power 0.1 (uWatts) RX Power 0.1 (uWatts) (output - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 49
DRAFT: BROCADE CONFIDENTIAL show processes cpu 2 show processes cpu Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays information about the active processes in the switch and their corresponding CPU utilization statistics. show processes cpu - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 50
BROCADE CONFIDENTIAL show processes memory Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays the memory usage information based KB To show memory usage information by individual processes: switch#show processes memory %Memory Used: 39.463%; - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 51
DRAFT: BROCADE CONFIDENTIAL show running-config 2 show running-config Synopsis Operands Defaults LLDP configuration. Displays the Remote Monitoring Protocol (RMON) configuration. Displays the switch configuration. There are no default configurations for this command. Privileged EXEC mode Use - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 52
2 show startup-config DRAFT: BROCADE CONFIDENTIAL show startup-config Synopsis Operands Defaults Command : • An error displays if there are no entries in the startup configuration file, for example switch#show startup-config % No Startup-config • Use the write memory command to add entries to - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 53
DRAFT: BROCADE CONFIDENTIAL show system 2 show system Synopsis Operands FC Port(s) Tengig Port(s) Up Time FOS Version Jumbo Capable Burned In MAC Management IP Status : switch : Online : 76.6 : 8 : 24 : 18:28:27 up 4:09 : v6.1.2 : yes : 00:05:1E:76:42:00 : 10.35.155.204 : UP -- Power Supplies - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 54
, Inc. Build Time: 03:35:17 Feb 18, 2009 switch uptime: 04:11:09 Firmware name: v6.1.2 Switch Model Name: Brocade 8000 Control Processor: Freescale Semiconductor 8548E with 1016 MB of memory 4MB of boot flash memory. 8 FC Port(s) 24 Ten GigabitEthernet/IEEE 802.3 interface(s) show running-config - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 55
DRAFT: BROCADE CONFIDENTIAL show users 2 show users Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples Displays information on all users currently logged into the switch. show users none There are no default configurations for this command. Privileged EXEC mode Use - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 56
2009 E209 uptime: 04:14:43 Firmware name: v6.1.2 Switch Model Name: Brocade 8000 Control Processor: Freescale Semiconductor 8548E with 1016 MB of memory 4MB of boot flash memory. 8 FC Port(s) 24 Ten GigabitEthernet/IEEE 802.3 interface(s) switch# show system 38 Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 57
DRAFT: BROCADE CONFIDENTIAL terminal length 2 terminal length Synopsis Operands Defaults Command Modes Description Usage the number of lines to display on the screen. If 0 (zero), the switch does not pause between screens of output. To set the number of lines to display on the screen to 30 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 58
2 terminal monitor DRAFT: BROCADE CONFIDENTIAL terminal monitor Synopsis Operands Defaults Command Modes Description To enable the display of the RASlog and the debug outputs on a terminal: switch#terminal monitor To disable the display of the RASlog and the debug outputs on a terminal: switch# - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 59
DRAFT: BROCADE CONFIDENTIAL write erase Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Removes the startup configuration from the switch. write erase none There are no default configurations for this command. Privileged EXEC mode Use this command to remove - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 60
2 write memory DRAFT: BROCADE CONFIDENTIAL write memory Synopsis Operands Defaults Command Modes Description Usage no usage guidelines for this command. To write configuration data to a file: switch#write memory Overwrite the startup config file (y/n): y Building configuration... write erase 42 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 61
BROCADE CONFIDENTIAL VLAN Commands Chapter 3 fcf forward Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Enables guidelines for this command. To enable FC forwarding on a VLAN interface: switch(config)#interface vlan 777 switch(conf-if-vl-777)#fcf forward - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 62
3 interface vlan DRAFT: BROCADE CONFIDENTIAL interface vlan Synopsis Operands Defaults Command Modes Description a VLAN interface. All of the ports on the switch are a part of the default VLAN 1. To create a VLAN with ID 56: switch(config)#interface vlan 56 switch-cmsh(conf-if-vl-56)# interface - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 63
BROCADE CONFIDENTIAL show interface 3 show interface Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays the configuration and status of an interface. show interface [tengigabitethernet slot/port | port interface: switch#show : access : enable : all : - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 64
3 show vlan DRAFT: BROCADE CONFIDENTIAL show vlan Synopsis Operands Defaults Command Modes usage guidelines for this command. To show information on a VLAN: switch#show vlan 1 VLAN Name State Ports (u)-Untagged, (t)-Tagged (c)-Converged 1 default ACTIVE Te 0/0(t) Te 0/4(t) - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 65
BROCADE CONFIDENTIAL show vlan classifier 3 show vlan classifier Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays information about a specific VLAN classifier group. show vlan classifier [group number | interface group number | port 1: switch#show - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 66
BROCADE CONFIDENTIAL switchport Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Puts the interface to Layer 2 mode and sets the switching to set the switching characteristics of the Layer 2 interface. Use the no switchport command to take the switch out of - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 67
BROCADE CONFIDENTIAL switchport access 3 switchport access Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Sets the Layer 2 interface as access. switchport access vlan vlan_id no switchport access vlan vlan vlan_id Sets the port to 100: switch(conf-if- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 68
3 switchport converged DRAFT: BROCADE CONFIDENTIAL switchport converged Synopsis Operands Defaults Command Modes Description Usage converged allowed vlan add 100 To remove the tagged VLAN 100 from the interface: switch(conf-if-te-0/19)#switchport converged allowed vlan remove 100 show vlan brief, - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 69
DRAFT: BROCADE CONFIDENTIAL switchport mode 3 switchport mode Synopsis Operands Defaults Command Modes set the mode of the interface to trunk: switch(conf-if-te-0/19)#switchport mode trunk To set the mode of the interface to converged: switch(conf-if-te-0/19)#switchport mode converged show vlan - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 70
3 switchport trunk DRAFT: BROCADE CONFIDENTIAL switchport trunk Synopsis Operands Defaults Command Modes Description Usage truck allowed vlan add 100 To remove the tagged VLAN 100 from the interface: switch(conf-if-te-0/19)#switchport truck allowed vlan remove 100 show vlan brief, show - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 71
DRAFT: BROCADE CONFIDENTIAL vlan classifier activate group 3 vlan classifier activate group Synopsis are no usage guidelines for this command. To activate VLAN classifier group 1 for VLAN 5: switch-cmsh(conf-if-te-0/10)#vlan classifier activate group 1 vlan 5 none Converged Enhanced Ethernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 72
3 vlan classifier group DRAFT: BROCADE CONFIDENTIAL vlan classifier group Synopsis Operands Defaults Command Modes guidelines for this command. To add rule 1 to VLAN classifier group 1: switch(config)#vlan classifier group 1 add rule 1 none 54 Converged Enhanced Ethernet Command Reference 53 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 73
DRAFT: BROCADE CONFIDENTIAL vlan classifier rule 3 vlan classifier rule Synopsis Operands Defaults To create an fcoe VLAN classifier rule: switch(config)#vlan classifier rule 2 proto fcoe encap ethv2 To create a MAC-based VLAN classifier rule: switch(config)#vlan classifier rule 2 mac 0000.0000 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 74
3 vlan classifier rule DRAFT: BROCADE CONFIDENTIAL 56 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 75
DRAFT: BROCADE CONFIDENTIAL Interface Commands Chapter 4 clear counters Synopsis Operands Description Defaults Command Modes User Guidelines Example Clears statistics on all interfaces on the switch. clear counters {all | access-list mac access_list_name | [interface port-channel number | - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 76
4 clear counters DRAFT: BROCADE CONFIDENTIAL See Also show interfaces 58 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 77
DRAFT: BROCADE CONFIDENTIAL description 4 description Synopsis Operands Defaults Command Modes guidelines for this command. To set the string describing tengigabitethernet interface 0/1: switch(conf-if-te-0/1)#description converged_101 none Converged Enhanced Ethernet Command Reference 59 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 78
: BROCADE CONFIDENTIAL interface Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Enters the interface configuration mode to configure an interface. interface [port-channel number | tengigabitethernet slot/port | vlan vlan id] no interface [port-channel - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 79
DRAFT: BROCADE CONFIDENTIAL mtu 4 mtu Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Specifies the MTU on the interface. mtu size size Specifies the - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 80
BROCADE CONFIDENTIAL show interface Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples show interface [port-channel number | tengigabitethernet slot/port | switchport ] port-channel number Specifies to display the port Ethernet interface 0/1: switch#show interface - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 81
:17 To display Layer 2 information for all interfaces: switch#show interface switchport Interface name Switchport mode Ingress filter Acceptable frame types Default Vlan Active Vlans Inactive Vlans : TenGigabitEthernet 0/8 : access : enable : all : 1 : 1 : - Interface name Switchport mode Ingress - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 82
in the summary format: switch#show ip interface brief Interface IP-Address ======== ========== Port-channel 10 unassigned Port-channel 11 unassigned Port-channel 12 unassigned Port-channel 13 unassigned Port-channel 14 unassigned Port-channel 15 unassigned TenGigabitEthernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 83
DRAFT: BROCADE CONFIDENTIAL show ip interface 4 See Also TenGigabitEthernet 0/13 TenGigabitEthernet 0/14 TenGigabitEthernet 0/15 TenGigabitEthernet 0/16 TenGigabitEthernet 0/17 TenGigabitEthernet 0/18 TenGigabitEthernet 0/19 TenGigabitEthernet 0/20 TenGigabitEthernet 0/21 TenGigabitEthernet 0/ - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 84
4 shutdown DRAFT: BROCADE CONFIDENTIAL shutdown Synopsis Operands Defaults Command Modes Description Usage usage guidelines for this command. To disable an interface: switch(conf-if-te-0/1)#shutdown To enable an interface: switch(conf-if-te-0/1)#no shutdown interface, show ip interface, show - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 85
DRAFT: BROCADE CONFIDENTIAL Link Layer Discovery Protocol Commands Chapter 5 advertise dcbx-fcoe-app-tlv Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Advertises application - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 86
DRAFT: BROCADE CONFIDENTIAL 5 advertise dcbx-fcoe-logical-link-tlv advertise dcbx-fcoe-logical-link-tlv Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Advertises - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 87
DRAFT: BROCADE CONFIDENTIAL advertise dcbx-tlv 5 advertise dcbx-tlv Synopsis Operands , Length, Values (TLVs). advertise dcbx-tlv no advertise dcbx-tlv none Advertise is enabled. Protocol LLDP configuration mode Advertises to any attached device mandatory Data Center Bridging eXchange protocol - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 88
5 advertise dot1-tlv DRAFT: BROCADE CONFIDENTIAL advertise dot1-tlv Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Advertises to any attached device IEEE 802.1 organizationally specific Type, - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 89
DRAFT: BROCADE CONFIDENTIAL advertise dot3-tlv 5 advertise dot3-tlv Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Advertises to any attached device IEEE 802.3 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 90
-tlv management-address Specifies the management address of the system. port-description Describes the user configured port. system-capabilities Specifies the capabilities of the system. system-description Describes the system firmware version and the current image running on the system. system - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 91
DRAFT: BROCADE CONFIDENTIAL clear neighbor information. slot Specifies a valid slot number. port Specifies a valid port number. There are no default configurations for this command the LLDP information for all interfaces: switch#clear lldp neighbors show lldp neighbors Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 92
statistics DRAFT: BROCADE CONFIDENTIAL clear lldp statistics Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Clears LLDP statistics for all interfaces or a specified interface. clear lldp statistics interface [tengigabitethernet slot/port] interface Use - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 93
DRAFT: BROCADE CONFIDENTIAL debug lldp packet 5 debug lldp packet Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Enables debugging for Link Layer Discovery Protocol (LLDP). debug lldp packet {all | interface tengigabitethernet slot/port} [both | detail - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 94
5 description DRAFT: BROCADE CONFIDENTIAL description Synopsis Operands Defaults Command Modes Description Usage Guidelines for this command. To set the strings describing LLDP: switch(conf-lldp)#description Brocade-LLDP none 76 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 95
DRAFT: BROCADE CONFIDENTIAL hello 5 hello Synopsis Operands Defaults Command Modes To set the time interval to 10 seconds between the transmissions: switch#configure terminal switch (config) #protocol lldp switch(conf-lldp)#hello 10 none Converged Enhanced Ethernet Command Reference 77 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 96
5 lldp dcbx-version DRAFT: BROCADE CONFIDENTIAL lldp dcbx-version Synopsis Operands Defaults pre-cee Specifies to auto adjust the DCBX protocol version to accommodate the difference when a switch interacts with different vendors using a different version of the DCBX protocol. Specifies to use - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 97
this command to disable LLDP on the interface. Use the no lldp disable command to enable LLDP on the interface. There are no usage guidelines for this command. To disable LLDP on the interface. switch(conf-if-te-0/1)#lldp disable none Converged Enhanced Ethernet Command Reference 79 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 98
5 lldp fcoe-priority-bits DRAFT: BROCADE CONFIDENTIAL lldp fcoe-priority-bits Synopsis Operands Defaults set the priorities on which FCoE traffic will be allowed: switch(conf-if-te-0/1)#lldp fcoe-priority-bits 0xff protocol lldp 80 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 99
DRAFT: BROCADE CONFIDENTIAL lldp profile 5 lldp profile Synopsis Operands Defaults Command Modes Description configuration are used. To apply an LLDP profile on an interface: switch(conf-if-te-0/1)#lldp profile test protocol lldp Converged Enhanced Ethernet Command Reference 81 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 100
5 mode DRAFT: BROCADE CONFIDENTIAL mode Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Sets the LLDP mode on the switch. mode tx | rx no mode tx Specifies to enable only the transmit mode. rx Specifies to enable only the receive mode. Both transmit - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 101
DRAFT: BROCADE CONFIDENTIAL multiplier 5 multiplier Synopsis Operands Defaults Command Modes Description Usage Guidelines guidelines for this command. To set the number of consecutive misses: switch(conf-lldp)#multiplier 2 hello Converged Enhanced Ethernet Command Reference 83 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 102
5 profile DRAFT: BROCADE CONFIDENTIAL profile Synopsis Operands Defaults Command Modes Description profiles can be created. To create a profile named test: switch(conf-lldp)#profile test To delete a profile named test: switch(conf-lldp)#no profile test lldp profile 84 Converged Enhanced Ethernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 103
are enabled. Global configuration mode Use this command to enter LLDP configuration mode to be able to make changes to the parameters. Use the no protocol lldp command to return to the default setting. There are no usage guidelines for this command. To clear all LLDP configurations: switch(config - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 104
5 show debug lldp DRAFT: BROCADE CONFIDENTIAL show debug lldp Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays the LLDP debugging status on the switch. show debug lldp none There are no default configurations for this command. EXEC mode Use this - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 105
a selected interface: switch#show lldp interface tengigabitethernet 0/0 LLDP information for Te 0/0 State: Enabled Mode: Receive/Transmit Prim DCBX FCoE Priority Bits: 0x8 Port ID IEEE DCBX DCBX FCoE Logical Link Brocade Link none Converged Enhanced Ethernet Command Reference 87 53- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 106
1020 (MAC) Remote Mac: 0005.1e76.102c OPTIONAL TLVs Port Interface Description: Te 0/8 System Name: sw0 System Description: Fibre Channel Switch. System Capabilities: Switching Routing System Capabilities Enabled: Switching Link Prim: 257 Remote Protocols Advertised: Multiple Spanning Tree Protocol - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 107
BROCADE CONFIDENTIAL show lldp neighbors 5 See Also Link Aggregation Status: Disabled Port Vlan Id: 1 Port & Protocol Vlan Flag: Supported Not enabled Port & Protocol Vlan Id: 0 Link Aggregation Port 0 MaxVersion: 0 EN: 1 Will: 0 Err: 0 User-Pri-Map: 0x00 FCoE LLS OperVersion: 0 MaxVersion: 0 EN - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 108
BROCADE CONFIDENTIAL show lldp statistics Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays the LLDP statistics on all interfaces or a specified interface. show lldp statistics [interface tengigabitethernet slot/port interface: switch#show lldp - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 109
DRAFT: BROCADE CONFIDENTIAL system-description LINE 5 system-description LINE Synopsis Operands Defaults this command. To set the global system description specific to LLDP: switch(conf-lldp)#system-description Brocade system-name Converged Enhanced Ethernet Command Reference 91 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 110
values is a maximum of32 characters. By default, the host name from the switch is used. Protocol LLDP configuration mode Use this command to set the global system name for the LLDP: switch(conf-lldp)#system-name Brocade system-description 92 Converged Enhanced Ethernet Command Reference 53- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 111
the 802.3ad standard-based LAG. Specifies the Brocade proprietary hardware-based trunking. By default, the type is set to standard. Interface configuration mode Use this command to add an interface to a port-channel specified by the channel-group number. This command enables link aggregation on - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 112
6 channel-group DRAFT: BROCADE CONFIDENTIAL See Also switch(conf-if)#channel-group 4 mode active interface port-channel 94 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 113
command to clear the LACP counters per specified channel-group. There are no default configurations for this command. To clear the LACP counters for a specific port-channel: switch#clear lacp 10 counters show lacp counters Converged Enhanced Ethernet Command Reference 95 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 114
command. Privileged EXEC mode Use this command to clear the LACP counters for all port-channels. There are no default configurations for this command. To clear the counters for all port-channels: switch#clear lacp counters show lacp 96 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 115
DRAFT: BROCADE CONFIDENTIAL debug lacp 6 debug lacp Synopsis Operands Enables debugging for the Link Aggregation Control Protocol (LACP). debug lacp {all | cli | event | nsm | pdu {rx {all | interface tengigabitethernet slot/port} | tx {all | interface tengigabitethernet slot/port} }| sync | - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 116
6 debug lacp DRAFT: BROCADE CONFIDENTIAL Examples See Also To enable debugging of LACP PDUs for transmitted and received packets on all interfaces: switch#debug lacp pdu tx all switch#debug lacp pdu rx all switch#show debug lacp LACP rx debugging is on LACP tx debugging is on show debug lacp 98 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 117
DRAFT: BROCADE CONFIDENTIAL lacp system-priority 6 lacp system-priority Synopsis Operands Defaults To set the LACP system-priority to 68: switch(config)#lacp system-priority 68 To clear the configured LACP system-priority: switch(config)#no lacp system-priority none Converged Enhanced Ethernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 118
. Interface configuration mode Use this command to set the short timeout value for Brocade trunks or to set the long timeout value for standard trunks. Use the the LACP short timeout value to 5 seconds: switch(conf-if-te-0/1)#lacp timeout short 5 none 100 Converged Enhanced Ethernet Command Reference - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 119
BROCADE CONFIDENTIAL show lacp counter 6 show lacp counter Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays the Link Aggregation Control Protocol (LACP) counters on all port port-channel 10: switch#show lacp counter 10 % Traffic statistics Port - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 120
6 show lacp-sys-id DRAFT: BROCADE CONFIDENTIAL show lacp-sys-id Synopsis Operands Defaults Command Modes globally administered individual MAC addresses associated with the system. To display the local system ID: switch#show lacp sys-id % System 8000,00-05-1e-76-1a-a6 none 102 Converged Enhanced Ethernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 121
the system with details about the LACP counters on their member links. If you do not specify a port-channel, all port-channels are displayed. To display information for port-channel 10: switch#show port-channel 10 % Aggregator Po 10 0 Admin Key: 0010 - Oper Key 0010 Partner System ID: 0x0000,00-00 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 122
6 show port-channel DRAFT: BROCADE CONFIDENTIAL 104 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 123
BROCADE Ethernet interface. slot Specifies a valid slot number. port Specifies a valid port number. vlan vlan_id Specifies the VLAN number. The MAC address table. The vlan keyword is mandatory because the switch only supports independent VLAN learning (IVL). To add the static address 0011.2222 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 124
7 mac-address-table DRAFT: BROCADE CONFIDENTIAL See Also To set the aging time to 10 minutes: switch(config)#mac-address-table aging-time 600 show mac address-table static 106 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 125
DRAFT: BROCADE CONFIDENTIAL slot/port | port-channel number} | linecard interface tengigabitethernet slot/port | static | vlan vlan_id ] address mac-address Specifies a 48-bit display a specific MAC address in the table: switch#show mac-address-table address 0011.2222.3333 Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 126
7 show mac-address-table DRAFT: BROCADE CONFIDENTIAL See Also VlanId Mac-address Type 100 0011.2222.3333 Static Total MAC addresses : 1 State Inactive Ports Te 0/1 To display the aging time for a specific MAC address table: switch#show mac-address-table aging-time MAC Aging-time : 300 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 127
DRAFT: BROCADE CONFIDENTIAL Layer 2 ACL commands Chapter 8 clear counters access-list mac are cleared. There are 255 ACL counters supported per port group. To clear counters for the configured MAC access list named test on an interface: switch#clear counters access-list mac test interface - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 128
based on the source and destination MAC addresses and the protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported per port destination MAC address 0022.3333.5555 and to enable the counting of packets: switch(conf-macl-ext)#deny 0022.3333.4444 0022.3333 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 129
DRAFT: BROCADE CONFIDENTIAL deny (extended ACLs) 8 See Also switch(conf-macl-ext)#no deny 0022.3333.4444 0022.3333.5555 ipv4 mac-access-list extended, mac-access-list standard, permit Converged Enhanced Ethernet Command Reference 111 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 130
drop traffic based on the source MAC address. You can also enable counters for a specific rule. There are 255 ACL counters supported per port group. Use and to enable the counting of packets: switch(conf-macl-std)#deny 0022.3333.4444 count To delete a rule from a MAC standard ACL: switch(conf-macl- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 131
BROCADE access list. If the ACL is already created, this command puts the switch in the extended MAC access-list configuration mode. Use the no mac to remove the access list. Extended ACLs allow you to filter traffic based on the following: • Source MAC address • Destination MAC address • - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 132
DRAFT: BROCADE CONFIDENTIAL mac access list. If ACL is already created, this command puts the switch in the standard MAC access-list configuration mode. Use the no remove the access list. Standard ACLs allow you to filter traffic based on the source MAC address. You can apply named MAC standard - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 133
DRAFT: BROCADE CONFIDENTIAL mac access-group 8 mac access-group Synopsis Operands Default packet is received on an interface with a MAC ACL applied, the switch checks the rules in the ACL. If any of the rules match, the switch permits or drops the packet, according to the rule. If the specified - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 134
based on the source and destination MAC addresses, and the protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported per port destination MAC address 0022.3333.5555 and to enable the counting of packets: switch(conf-macl-ext)#permit 0022.3333.4444 0022. - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 135
DRAFT: BROCADE CONFIDENTIAL permit (extended ACLs) 8 See Also To delete a filter rule in a MAC extended ACL: switch(conf-macl-ext)#no permit 0022.3333.4444 0022.3333.5555 ipv4 mac-access-list extended, mac-access-list standard, no seq Converged Enhanced Ethernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 136
permit traffic based on the source MAC address. You can also enable counters for a specific rule. There are 255 ACL counters supported per port group. and to enable the counting of packets: switch(conf-macl-std)#permit 0022.3333.4444 count To delete a rule from a MAC standard ACL: switch(conf-macl- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 137
DRAFT: BROCADE CONFIDENTIAL resequence access-list mac 8 resequence access-list mac of new sequence numbers to entries of an existing access list. To reorder the rules in a MAC ACL: switch#show running-config access-list mac test ! mac access-list standard test seq 1 permit 0011.2222.3333 seq - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 138
8 seq (extended MAC ACLs) DRAFT: BROCADE CONFIDENTIAL seq (extended MAC ACLs) Synopsis Operands Defaults drops traffic based on the source and destination MAC addresses, and the protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported per port group. - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 139
DRAFT: BROCADE CONFIDENTIAL seq (extended MAC ACLs) 8 Example See Also To create a rule in a MAC extended ACL to permit or drop IPv4 traffic from the source MAC address 0022.3333.4444 to the destination MAC address 0022.3333.5555 and to enable the counting of packets: switch(conf-macl-ext)#seq - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 140
DRAFT: BROCADE CONFIDENTIAL based on source and destination MAC address and protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported per port and to enable the counting of packets: switch(conf-macl-std)#seq 100 deny 0022.3333.4444 count switch(conf-macl- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 141
: BROCADE CONFIDENTIAL show mac access-group 8 show mac access-group Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays the current MAC ACL mapping to interfaces. show mac access-group [interface port-channel number | tengigabitethernet slot/port - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 142
DRAFT: BROCADE CONFIDENTIAL 8 show statistics access-list mac show statistics access-list mac Synopsis Operands Defaults Command Modes Description Examples See Also Shows active ACL rules in the switch and if the rules have counters enabled. show statistics access-list mac name [interface port- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 143
DRAFT: BROCADE CONFIDENTIAL Spanning Tree Protocol switch#configure terminal switch(config)#protocol spanning-tree stp switch(conf-stp)#bridge-priority 8192 switch#configure terminal switch(config)#protocol spanning-tree rstp switch(conf-rstp)#bridge-priority 8192 switch#configure terminal switch - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 144
DRAFT: BROCADE CONFIDENTIAL cisco-interoperability Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Configures the switch to interoperate with some legacy Cisco switches. cisco-interoperability [disable| enable] disable enable Disables Cisco - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 145
clear spanning-tree counters for a 10 Gbps Ethernet interface: switch#clear spanning-tree counter interface tengigabitethernet 0/1 To clear spanning-tree counters for port-channel 23: switch#clear spanning-tree counter interface port-channel 23 show spanning-tree Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 146
9 debug spanning-tree DRAFT: BROCADE CONFIDENTIAL debug spanning-tree Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Enables debugging for the Spanning Tree Protocol. debug spanning-tree {all | bpdu {rx | tx {all | interface port-channel number | - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 147
remains in the disabled state unless the port is enabled manually. This command allows you to enable the interface from the disabled state. To bring the interface out of the disabled state: switch(conf-rstp)#error-disable-timeout enable error-disable-timeout interval Converged Enhanced Ethernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 148
DRAFT: BROCADE CONFIDENTIAL 9 error-disable-timeout interval error-disable-timeout interval this command. To set the timeout value to 10 seconds: switch(conf-rstp)#error-disable-timeout interval 10 error-disable-timeout enable 130 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 149
DRAFT: BROCADE CONFIDENTIAL forward-delay 9 forward-delay Synopsis Operands Defaults Command return to the blocking state to prevent a loop. • Blocking - An interface that can cause a switching loop, no user data is sent or received, but it might go to the forwarding state if the other links in - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 150
9 hello-time DRAFT: BROCADE CONFIDENTIAL hello-time Synopsis Operands Defaults Command Modes max-age>=2*(hello-time + 1) To configure spanning-tree bridge hello time to 5 seconds: switch(conf-stp)#hello-time 5 forward-delay, max-age 132 Converged Enhanced Ethernet Command Reference 53 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 151
DRAFT: BROCADE CONFIDENTIAL instance 9 instance Synopsis Operands Defaults Command Modes Description Usage Guidelines To map a VLAN to an MTSP instance: switch(conf-mstp)#instance 1 vlan 2, 3 switch(conf-mstp)#instance 2 vlan 4-6 switch(conf-mstp)#instance 1 priority 4096 show spanning-tree - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 152
9 max-age DRAFT: BROCADE CONFIDENTIAL max-age Synopsis Operands Defaults Command Modes Description - 1)>=max-age>=2*(hello-time + 1) To configure the maximum-age to 10 seconds: switch(conf-rstp)#max-age 10 hello-time, forward delay 134 Converged Enhanced Ethernet Command Reference 53-1001762- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 153
DRAFT: BROCADE CONFIDENTIAL max-hops 9 max-hops Synopsis Operands Defaults Command instances. To set the number of maximum hops to 25 for all MSTPs: switch(config)#protocol spanning-tree mstp switch(conf-mstp)#max-hops 25 show spanning-tree mst Converged Enhanced Ethernet Command Reference - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 154
BROCADE CONFIDENTIAL port-channel path-cost Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Sets the path-cost behavior. port : switch(conf-mstp)#port-channel path-cost custom To set the behavior for the path-cost to standard: switch(conf-mstp)#port-channel - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 155
DRAFT: BROCADE CONFIDENTIAL protocol spanning-tree 9 protocol spanning-tree Synopsis Operands Defaults may occur if you do not enable xSTP on all devices connected on both sides of parallel links. To enable the Spanning Tree Protocol: switch(config)#protocol spanning-tree stp show spanning - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 156
9 region DRAFT: BROCADE CONFIDENTIAL region Synopsis Operands Defaults Command Modes Description Usage sensitive. To assign a name to an MSTP region named brocade1: switch(config)#protocol spanning-tree mstp switch(conf-mstp)#region brocade1 revision, show spanning-tree 138 Converged Enhanced - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 157
DRAFT: BROCADE CONFIDENTIAL revision 9 revision Synopsis Operands Defaults Command Modes Description for this command. To set the configuration revision to 1: switch(config)#protocol spanning-tree mstp switch(conf-mstp)#revision 1 region, show spanning-tree Converged Enhanced Ethernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 158
BROCADE CONFIDENTIAL usage guidelines for this command. To display all STP information: switch#show spanning-tree Spanning-tree Mode: Multiple Spanning Tree Protocol CIST type: point-to-point Received BPDUs: 0; Sent BPDUs: 0 Port Te 0/8 enabled IfIndex: 67633408; Id: 8008; Role: Disabled; State: - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 159
BROCADE CONFIDENTIAL show spanning-tree 9 See Also Designated Port Id: 0; CIST Priority: 128 Designated Bridge: 0000.0000.0000.0000 CIST Port Link-type: point-to-point Received BPDUs: 0; Sent BPDUs: 0 Port Te 0/19 enabled IfIndex: 68354563; Id: 8013; Role: Disabled; State: Discarding Designated - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 160
port, designated port, alternate port and backup port. • Port states-discarding, learning, and forwarding. • Port types-edge port (PortFast), point-to-point, and shared port. There are no usage guidelines for this command. To display the status and parameters of the Spanning Tree Protocol: switch - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 161
display information on a 10 Gbps Ethernet interface: switch#show spanning-tree interface tengigabitethernet 0/0 Spanning-tree Mode: Rapid Spanning Tree Protocol Root Id: 8000.0005.1e76.1aa0 (self) Bridge Id: 8000.0005.1e76.1aa0 Port Te 0/0 enabled IfIndex: 67108864; Id: 8000; Role: Disabled; State - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 162
DRAFT: BROCADE CONFIDENTIAL 9 Port roles-root port, designated port, alternate port, and backup port. • Port states-discarding, learning, and forwarding. • Port types-edge port (PortFast), point-to-point, and shared port. To display the status and parameters of the MSTP instance information: switch - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 163
(s): 0 Bpdu-guard errdisable timeout: disabled Bpdu-guard errdisable timeout interval: 300 sec Migrate Time: 3 sec CIST Port Details Instance: 0; Vlans:1, 100 Port Te 0/0 enabled IfIndex: 67108864; Id: 8000; Role: Disabled; State: Discarding Designated External Path Cost: 0; Internal Path Cost - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 164
DRAFT: BROCADE CONFIDENTIAL 9 show spanning-tree mst detail Designated Bridge: 0000.0000.0000.0000 CIST Port Hello Time: 2 Number of forward- Link-type: point-to-point Received BPDUs: 0; Sent BPDUs: 0 Port Te 0/19 enabled IfIndex: 68354563; Id: 8013; Role: Disabled; State: Discarding Designated - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 165
DRAFT: BROCADE CONFIDENTIAL show spanning-tree mst detail 9 See Also Link-type: point-to-point Received BPDUs: 0; Sent BPDUs: 0 MSTI details show spanning-tree mst interface, show spanning-tree mst instance Converged Enhanced Ethernet Command Reference 147 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 166
BROCADE which to display information on the MSPT instance. port Specifies a valid port number for the interface for which to display guidelines for this command. To display information on MSTP instance 1: switch#show spanning-tree mst instance 1 interface tengigabitethernet 0/0 Instance: 1; - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 167
DRAFT: BROCADE CONFIDENTIAL show spanning-tree mst interface 9 show spanning-tree mst interface and the state of the port specific to each MSTI. There are no usage guidelines for this command. To display information for the MSTP interface: switch#show spanning-tree mst interface - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 168
9 shutdown DRAFT: BROCADE CONFIDENTIAL shutdown Synopsis Operands Defaults Command Modes Description Usage Guidelines disable STP globally: switch(config)#protocol spanning-tree rstp switch(conf-rstp)#shutdown To enable STP globally: switch(config)#protocol spanning-tree rstp switch(conf-rstp)#no - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 169
. Interface configuration mode Use this command to automatically identify the edge port. The port can become an edge port if no Bridge Protocol Data Unit (BPDU) is received. To enable automatic edge detection: switch(conf-if-te-0/1)#spanning-tree autoedge protocol spanning-tree Converged Enhanced - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 170
BROCADE CONFIDENTIAL spanning-tree cost .Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Changes an interface's spanning-tree port a greater chance of becoming root. To set the port cost to 128: switch(conf-if-te-0/1)#spanning-tree cost 128 show spanning- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 171
to the forwarding state, and skip the listening and learning states To enable a port to quickly transition to the forwarding state: switch(conf-if-te-0/1)#spanning-tree edgeport To set the edgeport BPDU filter for the port: switch(conf-if-te-0/1)#spanning-tree edgeport bpdu-filter To guard the - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 172
root DRAFT: BROCADE CONFIDENTIAL spanning-tree guard root Synopsis Operands Defaults Command Modes Description Usage Guidelines Note Examples See Also Enables the guard root to restrict which interface is allowed to be the spanning-tree root port or the path-to-the root for the switch. spanning - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 173
DRAFT: BROCADE CONFIDENTIAL spanning-tree hello-time 9 spanning-tree hello-time . Interface configuration mode Use this command to set the interval time between the BPDUs sent by the root switch. Use the no spanning-tree hello-time command to return to the default setting.This command is only - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 174
BROCADE CONFIDENTIAL spanning-tree instance Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Sets restrictions for the port . To set restrictions for the port of MSTP instance 1 with the cost of 40000: switch(conf-if-te-0/1)#spanning-tree instance - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 175
BROCADE CONFIDENTIAL spanning-tree link-type 9 spanning-tree link-type Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Enables of the link type. To specify the link type as shared: switch(conf-if-te-0/0)#spanning-tree link-type shared spanning-tree link- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 176
disables the interface and puts the interface in the ERR_DISABLE state. To enable a port to quickly transition to the forwarding state: switch(conf-if-te-0/1)#spanning-tree portfast To set the Port Fast BPDU filter for the port: switch(conf-if-te-0/1)#spanning-tree portfast bpdu-filter To guard the - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 177
BROCADE CONFIDENTIAL spanning-tree priority 9 spanning-tree priority Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Changes an interface's spanning-tree port this command. To configure the port priority to 16: switch(conf-if-te-0/1)#spanning-tree - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 178
BROCADE CONFIDENTIAL 9 spanning-tree restricted-role spanning-tree restricted-role Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Restricts the role of the port from becoming a root port To configure the port from becoming a root port: switch(conf-if-te - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 179
to restrict the topology change notification Bridge Protocol Data Units (BPDUs) sent on the port. There are no usage guidelines for this command. To restrict the TCN on a specific interface: switch(conf-if-te-0/1)#spanning-tree restricted-tcn show spanning-tree Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 180
example, a physical port can be a member of VLAN 1002 and VLAN 55 simultaneously. In addition, VLAN 1002 can have STP enabled and VLAN 55 can have STP disabled simultaneously. There are no usage guidelines for this command. To disable spanning tree on a specific interface: switch(config)#interface - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 181
the optimal scheme. spanning-tree tc-flush-standard no spanning-tree tc-flush-standard none MAC address flushing is enabled. Global configuration mode Use this command to flush the MAC address based on the optimal scheme. Use the no spanning-tree tc-flush-standard command to disable the MAC address - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 182
9 transmit-holdcount DRAFT: BROCADE CONFIDENTIAL transmit-holdcount Synopsis Operands Defaults Command Modes for this command. To change the number of BPDUs transmitted to 3 seconds: switch(conf-mstp)#transmit-holdcount 3 show spanning-tree mst detail 164 Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 183
DRAFT: BROCADE CONFIDENTIAL port Specifies a valid port number. interface Use this keyword to specify any of the following interfaces: port-channel number Specifies the interface is a port- in the IGMP protocol: switch#clear ip igmp group none Converged Enhanced Ethernet Command Reference 165 53 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 184
10 clear ip igmp groups DRAFT: BROCADE CONFIDENTIAL clear ip igmp groups Synopsis Operands Defaults Command Modes Description this command. To clear information for all groups in the IGMP protocol: switch#clear ip igmp groups none 166 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 185
DRAFT: BROCADE CONFIDENTIAL debug ip igmp all 10 debug ip igmp all Synopsis Displays all IGMP information. debug ip igmp {all | group [A.B.C.D [interface tengigabitethernet slot/port|interface port-channel number| interface vlan vlan_id]]} Operands Description Defaults Command Modes User - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 186
DRAFT: BROCADE CONFIDENTIAL 10 ip igmp last-member-query-interval ip igmp last-member-query-interval Synopsis Operands Description Defaults Command Modes User Guidelines Example See Also Sets the last member query interval. ip igmp last-member-query-interval milliseconds milliseconds Response - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 187
DRAFT: BROCADE CONFIDENTIAL ip igmp query-interval 10 ip igmp query-interval Synopsis Operands Description Defaults Command Modes User Guidelines query messages sent by the switch. There are no defaults for this command. Privileged EXEC Mode There are no user guidelines for this command. - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 188
BROCADE CONFIDENTIAL 10 ip igmp query-max-response-time ip igmp query-max-response-time Synopsis Operands Description Defaults Command Modes User value, less that the maximum response time. When this timer expires, the switch replies with a report, provided that no other host has responded yet. - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 189
command to return to the default setting. This command performs IGMP snooping at the interface level. To enable igmp globally: switch(config)# ip igmp snooping enable show ip igmp snooping, ip igmp snooping enable (VLAN version) Converged Enhanced Ethernet Command Reference 171 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 190
IGMP snooping at the VLAN interface level. To enable igmp for a specific VLAN interface, enter Interface VLAN mode and execute the following command: switch#ip igmp snooping enable show ip igmp snooping, ip igmp snooping enable (global version) 172 Converged Enhanced Ethernet Command Reference - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 191
DRAFT: BROCADE CONFIDENTIAL ip igmp snooping fast-leave 10 ip igmp snooping fast-leave Synopsis Operands Description Defaults Command Modes User Guidelines Example See Also Enables snooping fast-leave. ip igmp snooping fast-leave no ip igmp snooping fast-leave none IGMP snooping fast-leave - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 192
BROCADE CONFIDENTIAL ip igmp snooping mrouter Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Configures a VLAN port setting. To configure a VLAN port member to be a multicast router interface. switch#ip igmp snooping mrouter interface tengigabitethernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 193
BROCADE CONFIDENTIAL ip igmp snooping mrouter-timeout 10 ip igmp snooping mrouter-timeout Synopsis Operands Description Defaults Command Modes User multicast router ports are automatically learned. There are no defaults for this command. Privileged EXEC Mode There are no user guidelines for - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 194
to return to the default setting. Use no ip igmp snooping querier enable to disable this command. To enable the IGMP snooping querier feature: switch(conf-if-vl-1)#ip igmp snooping querier enable show ip igmp interface, show ip igmp snooping interface 176 Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 195
port Specifies a valid port number. port-channel number Specifies the interface is a port-channel. The range of valid values is 1-63. Using ip igmp static-group, packets to the group are fast-switched Privileged EXEC Mode User Guidelines Example See Also There are no user guidelines for this - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 196
10 show debug ip igmp DRAFT: BROCADE CONFIDENTIAL show debug ip igmp Synopsis Operands Description Defaults Command Modes User Guidelines Example See Also Displays the IGMP packets received and transmitted, as well as related events. show debug ip igmp none This command displays the - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 197
DRAFT: BROCADE CONFIDENTIAL show ip igmp groups 10 show ip igmp groups Synopsis Displays information related to learned groups in the IGMP protocol module. show ip igmp groups [A.B.C.D |detail [[interface tengigabitethernet slot/port |detail]|[interface port-channel number |detail]| [interface - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 198
snooping DRAFT: BROCADE CONFIDENTIAL show ip this command to display IGMP snooping information.display multicast router port related information for the specified VLAN, or to display snooping the IGMP snooping information for VLAN 5: switch#show ip igmp snooping interface vlan 5 none 180 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 199
DRAFT: BROCADE CONFIDENTIAL show running-config igmp 10 show running-config igmp Synopsis Operands Description Defaults Command Modes User Guidelines Example See Also Displays the IGMP configuration. show running-config igmp none This command displays the IGMP contents of the currently running - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 200
10 show running-config igmp DRAFT: BROCADE CONFIDENTIAL 182 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 201
DRAFT: BROCADE CONFIDENTIAL RMON Commands Chapter 11 rmon alarm Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples Sets alarm conditions. rmon alarm index snmp_oid interval seconds { - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 202
11 rmon alarm DRAFT: BROCADE CONFIDENTIAL See Also switch(config)#rmon alarm 100 1.3.6.1.2.1.16.1.1.1.5.65535 interval 5 absolute rising-threshold 10000 event 100 falling-threshold 1000 event 101 owner admin rmon event, show rmon 184 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 203
BROCADE identity of the owner. The collection of RMON statistics is not enabled. Interface configuration mode Use this command to collect Ethernet group statistics on 10 Gbps Ethernet interface 0/1: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#rmon collection stats - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 204
11 rmon event DRAFT: BROCADE CONFIDENTIAL rmon event Synopsis Operands Defaults Command Modes event configuration. There are no usage guidelines for this command. To configure an RMON event: switch(config)#rmon event 2 log description "My Errorstoday" owner gjack show rmon events 186 Converged - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 205
for this command. To display the RMON statistics: switch#show rmon statistics rmon collection index 4 Interface index is Id: 67108864 , Name : TenGigabitEthernet 0/0 Receive Statistics: 218903 packets, 14015626 bytes, 0 packs dropped Multicasts: 218884, Broadcasts: 18 Under-size : 0, Jabbers - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 206
11 show rmon DRAFT: BROCADE CONFIDENTIAL See Also Owner: RMON_SNMP Status: ok(1) To display the RMON events: switch#show rmon events event Index = 4 Description "My Description" Event type Log & SnmpTrap Event community name admin Last Time Sent = 00:00:00 Owner admin rmon - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 207
DRAFT: BROCADE CONFIDENTIAL QoS Commands Chapter 12 cee Synopsis Operands Defaults Command The CEE map applied on an interface should exist on the switch. To apply a CEE map on an interface: switch(conf-if-te-0/1)#cee demo Because the switch does not allow applying a CEE map that does not exist, - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 208
BROCADE model allows different CEE Provisioning on different interfaces. There is only a single scheduler policy supported scheduler policy. The global scheduler policy is based on the CEE Map with the highest create a CEE map: switch(config)#cee-map test To delete a CEE map: switch(config)#no cee-map - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 209
BROCADE . The range of valid values is 1-100. Enables the Priority-based Flow Control (PFC) for each priority that gets user priority groups PG% PFC Description 0 50 1 50 Y SAN N LAN See Also switch(config)#cee-map test switch(conf-ceemap)#priority-group-table 0 weight 50 pfc switch - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 210
BROCADE CONFIDENTIAL default CEE Priority mapping table matches the IEEE 802.1Q recommendation for systems supporting eight traffic classes. The 802.1Q maps CoS 0 (best effort) to values. Only a single CoS can be mapped to a PFC-enabled priority queue. The CoS number must be identical to the - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 211
DRAFT: BROCADE CONFIDENTIAL priority-table 12 TABLE 4 Priority 5 6 7 Mapping of incoming Priority-to-Priority Groups PGID 1 1 15.0 See Also switch(config)#ceemap test switch(conf-ceemap)#priority-table 1 1 0 1 1 1 1 15.0 cee, cee-map, priority-group-table Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 212
BROCADE CONFIDENTIAL qos cos Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Specifies the interface Class of Service all ingress traffic for user priority mapping. When switch(conf-if-te-0/2)#qos cos 2 To return the interface CoS value to the default: switch - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 213
DRAFT: BROCADE CONFIDENTIAL qos cos-mutation 12 qos cos-mutation Synopsis Operands Defaults Command Modes Description Usage map. To activate the CoS-to-CoS mutation QoS map on the interface: switch(conf-if-te-0/1)#qos cos-mutation test To remove the CoS-to-CoS mutation QoS map on the interface - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 214
DRAFT: BROCADE CONFIDENTIAL behavior is to match the IEEE 802.1Q recommendations for systems supporting eight Traffic Classes. Interface configuration mode Use this command to apply a CoS-to-Traffic Class QoS map to an interface: switch(conf-if-te-0/1)#qos cos-traffic-class test qos map cos-traffic - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 215
BROCADE to an outbound CoS value. The inbound CoS value is the user priority after any interface ingress QoS trust and Interface default CoS policy go through unchanged: switch(config)#qos map cos-mutation test 0 1 2 3 5 4 6 7 switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#qos - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 216
12 qos map cos-mutation DRAFT: BROCADE CONFIDENTIAL See Also qos cos-mutation, show qos maps 198 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 217
BROCADE is used as the packet user priority after applying the a scheduler queue and packet servicing policy. Use the no IEEE 802.1Q for systems supporting eight Traffic Classes. There switch(config)#qos map cos-traffic-class test 1 0 2 3 4 5 6 7 To delete a CoS-to-Traffic Class QoS map: switch - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 218
12 qos map cos-traffic-class DRAFT: BROCADE CONFIDENTIAL mTC0_WEIGHTmTC1_WEIGHTmTC2_WEIGHT mTC3_WEIGHT mTC4_WEIGHT mTC5_WEIGHT mTC6_WEIGHT mTC7_WEIGHTmTC0_WEIGHTmTC1_WEIGHTmTC2_WEIGHTmTC3_WEIGHTmTC4_WEIGHTmTC5_ WEIGHTmTC6_WEIGHTmTC7_WEIGHT 200 Converged Enhanced Ethernet Command Reference 53- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 219
DRAFT: BROCADE CONFIDENTIAL . All multicast Traffic Class packet expansion queues are serviced Deficit Weighted Round Robin (DWRR). This multicast Traffic 30 percent bandwidth, and Traffic Class 3 getting 40 percent bandwidth: switch(config)#qos queue multicast scheduler dwrr 10 20 30 40 To return - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 220
12 qos queue scheduler DRAFT: BROCADE CONFIDENTIAL qos queue scheduler Synopsis Operands percent. Sets the DWRR weight for Traffic Class 3 in units of bandwidth percentage left over after servicing all of the Strict Priority Traffic Classes. The sum of all weight values must equal 100 percent. - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 221
Traffic Classes are supported with a configurable number of them being Strict Priority and any remaining ones being serviced DWRR. This Traffic getting 30 percent bandwidth, and Traffic Class 3 getting 40 percent bandwidth: switch(config)#qos queue scheduler strict-priority 4 dwrr 10 20 30 40 To - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 222
DRAFT: BROCADE CONFIDENTIAL 12 qos rcv-queue multicast rate-limit qos rcv-queue rate limit is applied uniformly across the entire system. This rate limit is enforced independently by each switch. Use the no qos rcv-queue multicast rate-limit command to return the multicast packet expansion rate - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 223
DRAFT: BROCADE CONFIDENTIAL qos rcv-queue multicast threshold 12 qos rcv-queue multicast are applied uniformly across the entire system. These queue depths are enforced independently by each switch. Use the no qos rcv-queue multicast threshold command to return the multicast expansion queques - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 224
DRAFT: BROCADE CONFIDENTIAL qos with the Interface Default CoS. The CoS mode sets the user priority based on the incoming CoS value, if the incoming packet This command is not applicable for port-channel interfaces. To set the interface QoS to the trust mode: switch(conf-if-te-0/1)#qos trust cos - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 225
DRAFT: BROCADE CONFIDENTIAL show cee maps 12 show cee maps Synopsis command. To display information on all of the defined CEE maps: switch#show cee maps CEE Map test Precedence 1 Priority Group Table 0: Weight 50, PFC Enabled, TrafficClass 4, BW% 50 1: Weight 50, PFC Disabled, TrafficClass - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 226
BROCADE the 10 Gbps Ethernet port number within the linecard. model, then the command reports whether the Data Center Bridging eXchange protocol (DCBX) has overridden the user switch#show qos flowcontrol interface tengigabitethernet 0/1 Interface TenGigabitEthernet 0/1 Mode PFC DCBX enabled - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 227
BROCADE CONFIDENTIAL show qos interface 12 show qos interface Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples Displays a summary of all QoS configurations applied on an interface. show qos interface {tengigabitethernet slot/port interface: switch#show qos - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 228
12 show qos interface DRAFT: BROCADE CONFIDENTIAL See Also Traffic Class Scheduler configured for 0 Strict Priority queues TrafficClass: 0 1 2 3 4 5 6 7 DWRRWeight: 0 0 0 0 60 0 40 0 Multicast Packet Expansion Traffic Class Scheduler TrafficClass: 0 1 2 3 DWRRWeight: 25 25 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 229
DRAFT: BROCADE CONFIDENTIAL show qos maps 12 show qos maps Synopsis this command. To display information on the defined QoS maps: switch#show qos maps CoS-to-CoS Mutation map 'test' In-CoS: 0 1 2 3 4 5 6 7 Out-CoS: 0 1 2 3 5 4 6 7 Enabled on the following interfaces: Te 0/5 CoS-to-Traffic Class - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 230
DRAFT: BROCADE CONFIDENTIAL show linecard slot number. Specifies the 10 Gbps Ethernet interface port number within the linecard. Reports QoS statistics for all information for a 10 Gbps Ethernet interface: switch#show qos queue interface tengigabitethernet 0/2 Interface TenGigabitEthernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 231
BROCADE CONFIDENTIAL interface linecard slot number. Specifies the 10 Gbps Ethernet interface port number within the linecard. Reports QoS configurations for all the dataplane for a 10 Gbps Ethernet interface: switch#show qos rcv-queue interface tengigabitethernet 0/2 Interface TenGigabitEthernet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 232
: BROCADE CONFIDENTIAL interface linecard slot number. Specifies the 10 Gbps Ethernet interface port number within the linecard. Reports QoS multicast packet expansion a stand-alone switch, all ASICs are considered as slot number zero (0). To display the queueing information: switch#show qos rcv- - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 233
DRAFT: BROCADE CONFIDENTIAL Port Authentication Commands Chapter 13 clear dot1x statistics Synopsis Operands Defaults to clear all accumulated port authentication statistics on all ports. There are no usage guidelines for this command. To clear dot1x statistics: switch#clear dot1x statistics clear - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 234
Use this command to clear all of the dot1x statistics for a specific interface port. There are no usage guidelines for this command. To clear dot1x statistics on a port: switch#clear dot1x statistics interface tengigabitethernet 0/1 clear dot1x statistics 216 Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 235
authentication command to disable dot1x on the port and remove the configuration from 802.1X management. There are no usage guidelines for this command. To enable dot1x on a port: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#dot1x authentication none Converged Enhanced - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 236
13 dot1x enable DRAFT: BROCADE CONFIDENTIAL dot1x enable Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Enables 802.1X authentication globally. dot1x enable no dot1x enable none By default, authentication is disabled globally. Global configuration mode - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 237
-control command to return to the default setting. There are no usage guidelines for this command. To enable the port state to auto: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#dot1x port-control auto none Converged Enhanced Ethernet Command Reference 219 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 238
13 dot1x quiet-period DRAFT: BROCADE CONFIDENTIAL dot1x quiet-period Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Sets the number of seconds that a switch remains quiet between a failed authentication and an attempt to retry authentication. dot1x quiet - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 239
DRAFT: BROCADE CONFIDENTIAL dot1x reauthenticate interface 13 dot1x reauthenticate interface Synopsis for this command. To initiate reauthentication on interface tengigabitethernet 0/1: switch#dot1x reauthenticate interface tengigabitethernet 0/1 none Converged Enhanced Ethernet Command - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 240
this command. Interface configuration mode Use this command to enable reauthentication on a port. There are no usage guidelines for this command. To enable reauthentication on a port: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#dot1x reauthentication none 222 Converged - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 241
before a port changes to the unauthorized state. Use the no dot1x reauthMax command to return to the default setting. There are no usage guidelines for this command. To set the maximum number of reauthentication attempts to 5: switch(config)#interface tengigabitethernet 0/1 switch(conf-if - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 242
DRAFT: BROCADE CONFIDENTIAL 13 dot1x timeout re-authperiod dot1x timeout re-authperiod To set 25 seconds as the amount of time between reauthorization attempts: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#dot1x timeout re-authperiod 25 none 224 Converged Enhanced - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 243
DRAFT: BROCADE CONFIDENTIAL dot1x timeout server-timeout 13 dot1x timeout server-timeout this command. To set 40 seconds as the switch-to-authentication server transmission time: switch(config)#interface tengigabitethernet 0/1 switch(config-if)#dot1x timeout server-timeout 40 none Converged - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 244
DRAFT: BROCADE CONFIDENTIAL 13 dot1x timeout supp-timeout dot1x timeout supp-timeout Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Sets the time in seconds that a switch waits for a response to an Extensible Authentication Protocol (EAP) request frame - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 245
DRAFT: BROCADE CONFIDENTIAL dot1x timeout tx-period 13 dot1x timeout tx-period Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Sets the number of seconds that the switch waits for a response to an Extensible Authentication Protocol (EAP) request or - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 246
13 show dot1x DRAFT: BROCADE CONFIDENTIAL show dot1x Synopsis Operands Defaults Command Modes Description for this command. To display the state of the system: switch#show dot1x 802.1X Port-Based Authentication Enabled PAE Capability: Authenticator Only Protocol Version: 2 Auth Server: - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 247
BROCADE CONFIDENTIAL show dot1x all 13 show dot1x all Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples Displays detailed information for all of the ports all of the ports: switch#show dot1x all 802.1X Port-Based Authentication Enabled PAE Capability: - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 248
13 show dot1x all See Also none DRAFT: BROCADE CONFIDENTIAL 230 Converged Enhanced Ethernet Command Reference 53-1001762-01 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 249
BROCADE CONFIDENTIAL show dot1x diagnostics interface 13 show dot1x diagnostics interface Synopsis Operands Defaults Command Modes Description Usage Guidelines Examples See Also Displays all diagnostics information for the authenticator associated with a port with a port: switch#show dot1x - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 250
13 show dot1x interface DRAFT: BROCADE CONFIDENTIAL show dot1x interface Synopsis Operands Defaults Command Modes Ethernet interface 0/1: switch#show dot1x interface tengigabitethernet 0/1 Dot1x Global Status: Enabled 802.1X info for interface te0/1 Port Control: Auto Port Auth Status: - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 251
DRAFT: BROCADE CONFIDENTIAL show dot1x session-info interface 13 show dot1x session- display all statistical information of the established session: switch#show dot1x session-info interface tengigabitethernet 0/1 802.1X Session info for te0/1 User Name: testuser Session Time: 3 mins 34 - HP 8/80 | Converged Enhanced Ethernet Command Reference v6.4.0 (53-1001762-01, J - Page 252
DRAFT: BROCADE CONFIDENTIAL 13 show dot1x statistics interface show dot1x statistics usage guidelines for this command. To display the statistics for 10 Gbps Ethernet interface 0/1: switch#show dot1x statistics interface tengigabitethernet 0/1 802.1X statistics for interface te0/1 EAPOL Frames Rx:
53-1001762-01
30 March 2010
®
DRAFT: BROCADE CONFIDENTIAL
Converged Enhanced
Ethernet Command
Reference
Supporting Fabric OS v6.4.0