Home » HP Manuals » Laser Printers » HP CP6015dn » Manual Viewer

HP CP6015dn Service Manual - Page 131

REPLACE <COLOR> DRUM, Replace image drums

UPC - 883585363018

Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

The product uses four colors and has a different image drums for each color: black (K), magenta (M), cyan (C), and yellow (Y). Replace an image drum when the control panel displays REPLACE DRUM message. The control-panel display also indicates the color that should be replaced (if a genuine HP cartridge is currently installed). Replacement instructions are included in the image drum box. NOTE: If toner gets on clothing, wipe it off with a dry cloth and wash the clothes in cold water. Hot water sets toner into fabric. NOTE: Information about recycling used image drums is on the image drum box. Replace image drums 1. Grasp the grips on the sides of the front door and pull down to open. 2. With one hand, lift and slowly pull the used image drum out of the product. Grasp the blue handle with your other hand when accessible. NOTE: If reusing the same image drum, do not touch the green cylinder on the bottom of the drum because it can damage the drum. 3. Store the used image drum in a protective bag. Information about recycling used image drums is on the image drum box. 4. Remove additional image drums in the same manner. ENWW Replace supplies 89

Section	Page
Product basics	43
Quick access to product information	44
Product comparison	45
Product features	46
Product walkaround	49
Front view	49
HP Color LaserJet CP6015n, HP Color LaserJet CP6015dn, and HP Color LaserJet CP6015de	49
HP Color LaserJet CP6015x	50
HP Color LaserJet CP6015xh	50
Back view	51
Interface ports	52
Serial number and model number location	52
Supported operating systems	53
Control panel	55
Use the control panel	56
Control-panel layout	56
Interpreting control panel indicator lights	57
Control panel menus	58
Getting started basics	58
Menu hierarchy	59
Open the menus	59
Show Me How menu	60
Retrieve job menu	61
Information menu	62
Paper handling menu	63
Configure device menu	64
Printing menu	64
PCL sub-menu	64
Print Quality menu	66
System setup menu	71
Output Setup menu	77
I/O menu	80
Resets menu	85
Diagnostics menu	87
Service menu	91
Paper and print media	93
Supported paper and print media sizes	94
Supported paper types	98
Special paper or print media guidelines	100
Load paper and print media	101
Load Tray 1	101
Print envelopes	102
Load banner paper into Tray 1	102
Load Trays 2, 3, 4, or 5	102
Load standard-sized paper into Trays 2, 3, 4, or 5	102
Load undetectable standard-sized paper into Trays 2, 3, 4, and 5	104
Load custom-size paper into Tray 2, 3, 4, or 5	105
Load large-size paper into Tray 3, 4, or 5	106
Configure trays	108
Configure a tray when loading paper	108
Configure a tray to match print job settings	108
Configure a tray by using the Paper Handling menu	109
Automatic media type sensing (auto sense mode)	109
Auto-sense settings	109
Choose an output location	111
Standard output bin	111
Optional output accessories	111
3-bin stapler/stacker features	111
Booklet maker finisher features	111
Accessory walkaround	112
Configure the accessory operation mode	113
Select the operating mode at the control panel	113
Select the operating mode in the printer driver (Windows)	114
Select the operating mode in the printer driver (Mac OS X)	114
Manage and maintain the product	115
Information pages	116
HP Easy Printer Care	117
Open the HP Easy Printer Care software	117
HP Easy Printer Care software sections	117
Embedded Web server	120
Open the embedded Web server by using a network connection	120
Embedded Web server sections	121
Use HP Web Jetadmin software	123
Security features	124
Secure the embedded Web server	124
Secure Disk Erase	124
Data affected	124
Additional Information	125
Job storage	125
Lock the control-panel menus	125
Manage supplies	126
Print-cartridge storage	126
HP policy on non-HP print cartridges	126
HP fraud hotline and Web site	126
Replace supplies	127
Locate supplies	127
Supply replacement guidelines	127
Approximate replacement intervals for supplies	128
Change print cartridges	128
Change image drums	130
Install memory	133
Install DDR memory DIMMs	133
Enable memory for Windows	137
Install an HP Jetdirect or EIO print server card or EIO hard disk	138
Replace the staple cartridge	140
Replace saddle stitch staple cartridges in the booklet maker	142
Clean the product	145
Clean spilled toner	145
Clean the product exterior	145
Clean the product interior	145
Clean the 3X500 sheet input tray	147
Clean the IPTU	148
Upgrade the firmware	149
Determine the current firmware version	149
Download new firmware from the HP Web site	149
Transfer the new firmware to the product	149
Use FTP to upload the firmware through a browser	149
Use FTP to upgrade the firmware on a network connection using Microsoft Windows	150
Use HP Web Jetadmin to upgrade the firmware	150
Use MS-DOS commands to upgrade the firmware for USB connections	151
Upgrade the HP Jetdirect firmware	151
Set the real-time clock	153
Set the real-time clock	153
Theory of operation	155
Basic operation	156
Sequence of operation	156
Formatter system	158
Sleep mode	158
Resolution	159
Input/output	159
CPU	159
Memory	159
Hard disk	159
Random-access memory	159
DIMM slot	160
Firmware	160
Nonvolatile memory	160
PJL overview	160
PML	160
Control panel	160
Engine-control system	161
DC controller	162
Solenoids	162
Switches	163
Sensors	164
Motors and fans	165
Fuser control	167
Fuser temperature-control circuit	169
Fuser over-temperature protection	170
Fuser-failure detection	171
Fuser identification	171
Fuser-life detection	172
Relay-failure detection	172
Low-voltage power supply	172
Overcurrent/overvoltage protection	173
Safety	173
Voltage detection	173
Sleep (powersave) mode	173
High-voltage power supply	173
Laser/scanner system	176
Image-formation system	178
Image-formation process	179
Step 1: Pre-exposure	180
Step 2: Primary charging	180
Step 3: Laser-beam exposure	181
Step 4: Development	181
Step 5: Primary transfer	182
Step 6: Secondary transfer	182
Step 7: Separation	183
Step 8: Fusing	183
Step 9: ITB cleaning	184
Step 10: Drum cleaning	184
Print cartridge	185
Imaging drum	186
Developing roller engagement and disengagement	188
Intermediate transfer belt (ITB) unit	189
Primary-transfer-roller engagement and disengagement	190
ITB unit detection	191
Secondary-transfer-roller unit	193
Calibration	193
Color-misregistration contol	194
Image-stabilization control	195
Color-sensor control (duplex models only)	195
Gray-axis correction	197
Pickup, feed, and delivery system	198
Pickup-and-feed unit	201
Cassette pickup	203
Cassette paper-size and cassette-presence detection	203
Cassette lift operation	205
Cassette paper-level and paper-presence detection	206
Multifeed prevention	207
Multipurpose tray pickup	208
Multipurpose tray last-paper detection	209
Paper feed	210
Skew-feed prevention	212
Paper-type detection	213
Feed-speed control	213
Fusing and delivery unit	215
Loop control	215
Pressure-roller pressurization control	216
Duplexing unit	217
Duplexing reverse and feed control	218
Jam detection	219
Optional input trays	221
Paper-feeder pickup and feed operation	224
Removal and replacement	227
Removal and replacement strategy	228
Introduction	228
Required tools	229
Types of screws	229
Service approach	230
Before performing service	230
After performing service	230
Parts removal sequences	231
User-replaceable parts	232
Fuser	233
Transfer roller	236
Intermediate-transfer belt (ITB)	238
Tray-1 pickup and separation rollers	241
Tray-2, -3, -4, and -5 pickup rollers	243
Formatter	245
1 x 500-sheet input tray installation	248
3 x 500-sheet input tray installation	249
Tray 2	250
Trays 3, 4, and 5	250
Removal sequence 1	251
Secondary transfer unit	252
Multipurpose drive unit	257
Multipurpose-tray guide (Tray 1) unit	261
Cassette (Tray-2) pickup unit	262
Removal sequence 2	263
Rear-left cover	264
Rear-right cover	265
Rear cover	266
Low-voltage power supply unit	267
High-voltage power supply PCA (A)	268
Lifter drive unit	270
Removal sequence 2A	272
Fuser motor	272
Removal sequence 2B	273
Intermediate-transfer belt (ITB) motor	273
Removal sequence 2C	274
Face-down output bin	274
Left cover	275
Laser/scanner-fan duct	276
Removal sequence 2D	278
Print-cartridge driver PCA	278
Removal sequence 3	280
Rear-left cover	281
Face-down output bin	282
Left cover	283
High-voltage power supply PCA (B)	284
Formatter case	286
DC controller PCA	288
Removal sequence 3A	290
Environmental sensor	290
Removal sequence 4	291
Rear-left cover	292
Rear-right cover	293
Rear cover	294
Face-down output bin	295
Left cover	296
Print-cartridge driver PCA	297
Image-drum motor	299
Removal sequence 4A	301
Fuser fan	301
Removal sequence 4B	302
Print-cartridge feed motor (black)	302
Print-cartridge feed motor (yellow, magenta, and cyan)	303
Removal sequence 4C	304
Cartridge fan unit	304
Laser/scanner fan unit	305
Removal sequence 4D	306
Fuser power-supply unit	306
Primary-transfer-roller disengagement motor	307
Removal sequence 4 Sub-1	308
Print-cartridge drive unit (yellow and magenta)	309
Print-cartridge drive unit (cyan and black)	314
Print-cartridge interface PCA (cyan and black)	315
Main drive unit	316
Removal sequence 4 Sub-1A	318
Print-cartridge interface PCA (yellow and magenta)	318
Removal sequence 4 Sub-1B	319
Cartridge-fan duct	319
Removal sequence 5	320
Rear-left cover	321
Face-down output bin	322
Rear-upper cover	323
Control panel	324
Front-upper cover	326
Right-upper cover	327
Duplex switchback tray	328
Reverse cover	329
VOC fan	331
Duplexing reverse unit	332
Face-down delivery unit	333
Face-down cover	335
Removal sequence 5A	336
Scanner cover	336
Laser/scanner assembly (yellow and magenta)	337
Laser/scanner assembly (cyan and black)	339
Removal sequence 5B	341
Front door	341
Front-inner cover	342
Removal sequence 5C	343
Front-door assembly	343
Removal sequence 5D	344
Color-misregistration and image-density sensor unit	344
Removal sequence 5E	346
Pressure-release sensor unit	346
Removal sequence 6	347
Rear-left cover	348
Rear-right cover	349
Right-upper cover	349
Right-door assembly	350
Duplexing feed unit	352
Multipurpose-tray (Tray-1) pickup unit	354
Removal sequence 7	357
Thermopile unit	358
Front-lower cover	359
ITB duct	360
Optional input trays	361
1 x 500-sheet input tray	361
Right door	361
Lower-rear cover	363
Front-right cover	364
Right cover	365
Front-upper cover	366
Lower-left cover	367
Front-lower door	368
Box	369
Pickup unit	370
Input tray is not attached	370
Input tray is attached	371
Auto-close unit	373
Pickup motor	374
Paper-feeder driver PCA	375
3 x 500-sheet input tray	376
Right door	376
Lower-rear cover	376
Front-right cover	376
Right cover	376
Front-upper cover	376
Left cover	376
Pickup unit (middle cassette)	377
Pickup unit (lower cassette)	378
Pickup unit (upper cassette)	378
Input tray is not attached	378
Input tray is attached	379
Auto-close unit	381
Pickup motor	381
Paper-feeder driver PCA	381
Solve problems	383
Troubleshooting process	384
Determine the problem source	384
Pre-troubleshooting checklist	384
Troubleshooting checklist	385
Troubleshooting flowchart	386
Power subsystem	387
Power-on checks	387
Power-on troubleshooting overview	387
Tools for troubleshooting	389
Internal print-quality test pages	389
Diagnostics page	389
Configuration pages	390
Configuration page	390
HP embedded Jetdirect page	392
Embedded protocol page	393
Finding important information on the configuration pages	394
Solve performance problems	395
Solve connectivity problems	396
Solve direct-connect problems	396
Solve network connectivity problems	396
Solve network printing problems	396
Verify communication over the network	397
Control-panel message types	398
Control-panel messages	399
Event log messages	464
Print an event log	464
Show an event log	464
Sample event log	465
Clear the event log	465
Event log message	466
Paper-handling problems	470
Jams	470
Common causes of jams	470
Jam locations	471
Clear jams	471
Jam sensors	472
AREA 1: Jams in the output bin	473
AREA 2 and 3: Jams in the fuser and transfer area	475
AREA 4: Jams in the duplex area	482
AREA 5: Jams in Tray 2 and the internal paper path	487
AREA 6: Clear jams in Tray 1	491
Clear jams when printing banners	494
AREA 7: Jams in optional Trays 3, 4, and 5	497
AREA 8: Jams in the optional finishing devices	502
Clear jams in the output-accessory bridge	502
Clear jams in the sorter area	504
Clear jams in the booklet maker	506
Clear staple jams	508
Clear staple jams in the main stapler	508
Clear staple jams in the booklet maker	509
Jam recovery	512
Product feeds multiple sheets	513
Product pulls from incorrect tray	513
Product feeds incorrect page size	513
Paper does not feed automatically	514
Paper does not feed from Tray 2, 3, 4, or 5	514
Transparencies or glossy paper will not feed	515
Envelopes jam or will not feed in the product	515
Output is curled or wrinkled	516
Product will not duplex or duplexes incorrectly	516
Solve image-quality problems	518
Example print quality problems	518
Repetitive defects ruler	518
Overhead transparency defects	520
Print quality problems associated with the environment	520
Print quality problems associated with jams	520
Optimize and improve image quality	520
Use supported paper	521
Calibrate the product	521
Specify the correct paper type	521
Clean the fuser	522
Respond to control panel error messages	523
Clean the registration second transfer assembly	524
Use manual print modes	526
Print-quality-troubleshooting pages	527
Image-quality issues	529
Interface troubleshooting	535
Communication checks	535
EIO troubleshooting	535
Engine diagnostics	536
LED diagnostics	536
Understand lights on the formatter	536
HP Jetdirect LEDs	536
Heartbeat LED	537
Engine-test button	537
Diagnostics menu	538
Diagnostics mode	538
Diagnostics that put the engine into the special diagnostics mode	539
Diagnostic tests	539
Disable cartridge check	540
Paper-path sensors test	541
Paper-path test	543
Manual sensor test (special-mode test)	543
Manual sensor test 2 (special-mode test)	544
Component tests	545
Component test (special-mode test)	545
Print/stop test	549
Color-band test	549
Service mode functions	550
Service menu	550
Product resets	551
Restore factory-set defaults	551
Hard disk initialization	552
NVRAM initialization	552
Diagrams	553
Connectors	553
DC controller PCA	553
PCAs	553
Product base	556
1 x 500-sheet input tray	559
3 x 500-sheet input tray	559
IPTU	560
Sensors	560
Sensors	560
Product base	562
1 x 500-sheet input tray	565
3 x 500-sheet input tray	565
IPTU	566
Fans	567
Fans	567
Product base	568
Motors	568
Motors	568
Product base	570
1 x 500-sheet input tray	572
3 x 500-sheet input tray	572
IPTU	573
Solenoids	573
Solenoids	573
Product base	574
1 x 500-sheet input tray	575
3 x 500-sheet input tray	575
Switches	576
Switches	576
Product base	576
1 x 500-sheet input tray	577
3 x 500-sheet input tray	577
Block diagrams	579
Main assemblies	579
Main parts	582
PCAs	583
1 x 500-sheet input tray	584
3 x 500-sheet input tray	585
Intermediate paper-transfer unit (IPTU)	586
General timing chart	587
General circuit diagrams	588
Signals	592
Output accessories and intermediate paper-transfer unit (IPTU)	621
Theory of operation	622
Intermediate paper-transfer unit (IPTU)	622
Basic operation	622
Feed operation	624
Jam detection	624
3-bin stapler/stacker	625
Basic operation	625
Electrical circuitry	626
Feed drive system	626

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1,000
1,001
1,002
1,003
1,004
1,005
1,006
1,007
1,008
1,009
1,010
1,011
1,012
1,013
1,014
1,015
1,016
1,017
1,018
1,019
1,020
1,021
1,022
1,023
1,024
1,025
1,026
1,027
1,028
1,029
1,030
1,031
1,032
1,033
1,034
1,035
1,036
1,037
1,038
1,039
1,040
1,041
1,042
1,043
1,044
1,045
1,046
1,047
1,048
1,049
1,050
1,051
1,052
1,053
1,054
1,055
1,056
1,057
1,058
1,059
1,060
1,061
1,062

Match case Limit results 1 per page

The product uses four colors and has a different image drums for each color: black (K), magenta (M),

cyan (C), and yellow (Y).

Replace an image drum when the control panel displays

REPLACE <COLOR> DRUM

message. The

control-panel display also indicates the color that should be replaced (if a genuine HP cartridge is

currently installed). Replacement instructions are included in the image drum box.

NOTE:

If toner gets on clothing, wipe it off with a dry cloth and wash the clothes in cold water. Hot

water sets toner into fabric.

NOTE:

Information about recycling used image drums is on the image drum box.

Replace image drums

Grasp the grips on the sides of the front door and pull down to open.

With one hand, lift and slowly pull the used image drum out of the product. Grasp the blue handle

with your other hand when accessible.

NOTE:

If reusing the same image drum, do not touch the green cylinder on the bottom of the

drum because it can damage the drum.

Store the used image drum in a protective bag. Information about recycling used image drums is

on the image drum box.

Remove additional image drums in the same manner.

ENWW

Replace supplies