HP Deskwriter 600 DeskWriter 600 User's Guide - Not Orderable - Page 56

If Paper, Envelopes, Cards, Labels, or, Transparencies Don't Pass Through, the Printer

Get HP Deskwriter 600 PDF manuals and user guides View all HP Deskwriter 600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

SECTION FIVE If Paper, Envelopes, Cards, Labels, or Transparencies Don't Pass Through the Printer During normal printing, the printer picks up the top sheet, envelope, card, or transparency from the stack in the IN tray, prints on it, passes it to the OUT tray, and picks up the next top sheet from the stack in the IN tray. The exception to this process is when you use the single envelope slot. If the printer is not printing a single sheet at a time, or if the paper does not pass into or through the printer as expected, find the symptom in the following table that best matches the observed condition of your printer. For each listed symptom, more than one solution is usually possible. The first solution given is the most probable corrective action for the symptom. However, if that solution does not solve the problem, perform the other solutions in the order they appear until the problem is solved. N OT E For more information about using envelopes, see the ReadMe file. Symptom Paper does not get picked up from the IN tray. Solution The paper in the IN tray is not pressed against the paper feeder of the printer. Move the paper stack toward the printer until it presses against the paper feeder. The paper path in the printer is blocked. Remove the OUT tray, remove any paper from the IN tray, and lower the card guide if it is in the up position. Make sure the paper width adjuster is not preventing paper from loading. Reinstall the OUT tray and load paper. Too much paper is in the IN tray at one time. Remove a few sheets of paper. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
52
SECTION FIVE
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
If Paper, Envelopes, Cards, Labels, or
Transparencies Don’t Pass Through
the Printer
During normal printing, the printer picks up the top sheet,
envelope, card, or transparency from the stack in the IN tray,
prints on it, passes it to the OUT tray, and picks up the next top
sheet from the stack in the IN tray. The exception to this
process is when you use the single envelope slot. If the printer is
not printing a single sheet at a time, or if the paper does not
pass into or through the printer as expected, find the symptom
in the following table that best matches the observed condition
of your printer.
For each listed symptom, more than one solution is usually
possible. The first solution given is the most probable corrective
action for the symptom. However, if that solution does not solve
the problem, perform the other solutions in the order they
appear until the problem is solved.
N OTE
For more information about using envelopes, see the ReadMe file.
Symptom
Solution
Paper does not
get picked up
from the IN tray.
The paper in the IN tray is not pressed against the paper feeder of the
printer. Move the paper stack toward the printer until it presses against
the paper feeder.
The paper path in the printer is blocked. Remove the OUT tray, remove
any paper from the IN tray, and lower the card guide if it is in the up
position. Make sure the paper width adjuster is not preventing paper
from loading. Reinstall the OUT tray and load paper.
Too much paper is in the IN tray at one time. Remove a few sheets of
paper.