HP ML330 HP ProLiant ML330 Generation 3 Server Setup and Installation Guide - Page 124

ROMPaq Disaster Recovery, Power down the server. Refer to Server Operations.

Get HP ML330 - ProLiant - G3 PDF manuals and user guides
UPC - 613326960790
View all HP ML330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 124 highlights

Server Specific Troubleshooting 5. Power up the server. Refer to Chapter 2, "Server Operations." All configuration settings are now erased and all server operations halt. 6. When prompted during POST, power down the server. 7. Reset the position 6 switch to the default Off position. 8. Power up the server. 9. Reset all system configuration settings by pressing the F9 key (or the F8 key if you are using an ATA model) to run RBSU. For complete instructions on the use of RBSU, refer to Chapter 5, "Server Configuration and Utilities," or refer to the HP ROM-Based Setup Utility User Guide. ROMPaq Disaster Recovery If both the current and backup versions of the ROM are corrupt, perform ROMPaq disaster recovery procedures: 1. Create a ROMPaq diskette using the Autorun Menu on the SmartStart CD. 2. Power down the server. Refer to Chapter 2, "Server Operations." 3. Insert the ROMPaq diskette. 4. Power up the server. Refer to Chapter 2, "Server Operations." a. The server generates one long beep and two short beeps to indicate that you are in disaster recovery mode. If the diskette is not in place, the system continues to beep until a valid ROMPaq diskette is inserted. b. The ROMPaq diskette flashes both system ROM images. If successful, a sequence of ascending audible beeps is generated. If unsuccessful, a sequence of descending audible beeps is generated and you need to repeat the disaster recovery process. 5. Power down the server. 6. Remove the ROMPaq diskette. 7. Power up the server. HP ProLiant ML330 Generation 3 Server Setup and Installation Guide D-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Server Specific Troubleshooting
5.
Power up the server. Refer to Chapter 2, “Server Operations.”
All configuration settings are now erased and all server operations halt.
6.
When prompted during POST, power down the server.
7.
Reset the position 6 switch to the default
Off
position.
8.
Power up the server.
9.
Reset all system configuration settings by pressing the
F9
key (or the
F8
key if
you are using an ATA model) to run RBSU.
For complete instructions on the use of RBSU, refer to Chapter 5, “Server
Configuration and Utilities,” or refer to the
HP ROM-Based Setup Utility User
Guide
.
ROMPaq Disaster Recovery
If both the current and backup versions of the ROM are corrupt, perform ROMPaq
disaster recovery procedures:
1.
Create a ROMPaq diskette using the Autorun Menu on the SmartStart CD.
2.
Power down the server. Refer to Chapter 2, “Server Operations.”
3.
Insert the ROMPaq diskette.
4.
Power up the server. Refer to Chapter 2, “Server Operations.”
a.
The server generates one long beep and two short beeps to indicate that you
are in disaster recovery mode. If the diskette is not in place, the system
continues to beep until a valid ROMPaq diskette is inserted.
b.
The ROMPaq diskette flashes both system ROM images. If successful, a
sequence of ascending audible beeps is generated. If unsuccessful, a
sequence of descending audible beeps is generated and you need to repeat the
disaster recovery process.
5.
Power down the server.
6.
Remove the ROMPaq diskette.
7.
Power up the server.
HP ProLiant ML330 Generation 3 Server Setup and Installation Guide
D-13