HP ML330 HP ProLiant ML330 Generation 3 Server Setup and Installation Guide - Page 95

Build Array, Initialize Array, Delete Array F5, Restore Old Configuration F6, Edit Options F7

Get HP ML330 - ProLiant - G3 PDF manuals and user guides
UPC - 613326960790
View all HP ML330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

RAID Configuration and Management - Build Array-is used to rebuild the array using a spare drive. When Build Array starts, it prompts the user to select the target drive, and then the rebuild starts. This option applies only to RAID 1 and RAID 1+0 arrays. - Initialize Array-is used to clear the configuration information from drives attached to the Integrated ATA RAID controller. • Delete Array (F5)-allows you to delete a currently configured array. • Restore Old Configuration (F6)-restores the configuration that was there before you entered the utility. • Edit Options (F7)-edits the physical drive option status boxes located in the top right corner of the Physical Drive Information window. The options are as follows: - WC-OFF-enables or disables write cache. CAUTION: Enabling write cache may cause data loss or corruption during an unexpected loss of power. - DMA-ON-enables or disables DMA (direct memory access) transfers, in which data is transferred directly from the memory to the hard drive without microprocessor intervention. Pressing the F7 key allows you to enable or disable these options. Press the F7 key, move the cursor to the desired box, and then press the spacebar to check off the option. When enabled, the option status boxes change from red to green. • Save and Exit (F10)-saves the configuration and exits the utility. If you do not want to save the configuration or any changes that you have made, press the Esc key. Respond appropriately to the subsequent message boxes requiring confirmation. 6-6 HP ProLiant ML330 Generation 3 Server Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
RAID Configuration and Management
—
Build Array
—is
used to rebuild the array using a spare drive. When Build
Array starts, it prompts the user to select the target drive, and then the rebuild
starts. This option applies only to RAID 1 and RAID 1+0 arrays.
—
Initialize Array
—is used to clear the configuration information from drives
attached to the Integrated ATA RAID controller.
•
•
•
Delete Array (F5)
—allows you to delete a currently configured array.
Restore Old Configuration (F6)
—restores the configuration that was there
before you entered the utility.
Edit Options (F7)
—edits the physical drive option status boxes located in the
top right corner of the
Physical Drive Information
window. The options are as
follows:
—
WC-OFF
—enables or disables write cache.
CAUTION:
Enabling write cache may cause data loss or corruption during an
unexpected loss of power.
—
DMA-ON
—enables or disables DMA (direct memory access) transfers, in
which data is transferred directly from the memory to the hard drive without
microprocessor intervention.
Pressing the
F7
key allows you to enable or disable these options. Press the
F7
key, move the cursor to the desired box, and then press the spacebar to check off
the option. When enabled, the option status boxes change from red to green.
•
Save and Exit (F10)
—saves the configuration and exits the utility.
If you do not want to save the configuration or any changes that you have made,
press the
Esc
key. Respond appropriately to the subsequent message boxes
requiring confirmation.
6-6
HP ProLiant ML330 Generation 3 Server Setup and Installation Guide