HP ML330 HP ProLiant ML330 Generation 3 Server Setup and Installation Guide - Page 50

Storage Devices, Removing Bezel Blanks

Get HP ML330 - ProLiant - G3 PDF manuals and user guides
UPC - 613326960790
View all HP ML330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Hardware Options Installation Storage Devices The server ships standard with four removable media bays. The top 5.25-in bay is occupied by an IDE CD-ROM drive. The remaining three 5.25-in bays are available for removable media devices. You can install three half-height devices, or one full-height device and one half-height device, into these bays. Use the procedures in this section to install storage devices supported by the server. IMPORTANT: When you add or remove a component or change a security feature, you must reconfigure the server to recognize these changes. If the system configuration is incorrect, the server does not work properly and you may receive error messages on the screen. Removing Bezel Blanks When installing a device other than a hard drive into a removable media bay, you must remove the corresponding bezel blank from the front bezel. To remove a bezel blank: 1. Power down the server. Refer to "Powering Down the Server" in Chapter 2, "Server Operations." 2. Remove the Front Bezel. Refer to "Removing the Front Bezel" in Chapter 2, "Server Operations." HP ProLiant ML330 Generation 3 Server Setup and Installation Guide 4-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Hardware Options Installation
Storage Devices
The server ships standard with four removable media bays. The top 5.25-in bay is
occupied by an IDE CD-ROM drive. The remaining three 5.25-in bays are available
for removable media devices. You can install three half-height devices, or one
full-height device and one half-height device, into these bays.
Use the procedures in this section to install storage devices supported by the server.
IMPORTANT:
When you add or remove a component or change a security feature, you must
reconfigure the server to recognize these changes. If the system configuration is incorrect, the
server does not work properly and you may receive error messages on the screen.
Removing Bezel Blanks
When installing a device other than a hard drive into a removable media bay, you
must remove the corresponding bezel blank from the front bezel.
To remove a bezel blank:
1.
Power down the server. Refer to “Powering Down the Server” in Chapter 2,
“Server Operations.”
2.
Remove the Front Bezel. Refer to “Removing the Front Bezel” in Chapter 2,
“Server Operations.”
HP ProLiant ML330 Generation 3 Server Setup and Installation Guide
4-7