HP ML330 HP ProLiant ML330 Generation 3 Server Setup and Installation Guide - Page 64

Install the access panel and the front bezel. Refer to Server

Get HP ML330 - ProLiant - G3 PDF manuals and user guides
UPC - 613326960790
View all HP ML330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Hardware Options Installation 6. Slide the tape drive into the removable media bay. 7. Connect the end of the existing ATA cable to the IDE (ATAPI) connector on the system board. For the IDE connector location, refer to Chapter 1, "Component Identification." 8. Connect the cable connector labeled Device 1 to the tape drive. 9. Connect the cable connector labeled Device 0 to the CD-ROM drive. 10. Connect the next available power cable connector to the hard drive. 11. Install the access panel and the front bezel. Refer to Chapter 2, "Server Operations." HP ProLiant ML330 Generation 3 Server Setup and Installation Guide 4-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Hardware Options Installation
6.
Slide the tape drive into the removable media bay.
7.
Connect the end of the existing ATA cable to the IDE (ATAPI) connector on the
system board. For the IDE connector location, refer to Chapter 1, “Component
Identification.”
8.
Connect the cable connector labeled Device 1 to the tape drive.
9.
Connect the cable connector labeled Device 0 to the CD-ROM drive.
10.
Connect the next available power cable connector to the hard drive.
11.
Install the access panel and the front bezel. Refer to Chapter 2, “Server
Operations.”
HP ProLiant ML330 Generation 3 Server Setup and Installation Guide
4-21