HP ML330 HP ProLiant ML330 Generation 3 Server Setup and Installation Guide - Page 70

Expansion Boards, HP Internal Two-Bay Hot-Plug SCSI Drive, Cage Installation Instructions

Get HP ML330 - ProLiant - G3 PDF manuals and user guides
UPC - 613326960790
View all HP ML330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Hardware Options Installation 12. Connect the other end of the SCSI cable to the SCSI connector on the SCSI controller or optional array controller. For additional information, refer to the HP Internal Two-Bay Hot-Plug SCSI Drive Cage Installation Instructions. Expansion Boards To install an expansion board: 1. Complete the "Preparation Procedures" in this chapter. 2. From inside the chassis, push the expansion slot cover through the rear of the chassis. 3. Depending on the length of the expansion card, do one of the following: - If the card is full-length, go to step 4. - If the card is half-length, go to step 5. HP ProLiant ML330 Generation 3 Server Setup and Installation Guide 4-27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Hardware Options Installation
12.
Connect the other end of the SCSI cable to the SCSI connector on the SCSI
controller or optional array controller.
For additional information, refer to the
HP Internal Two-Bay Hot-Plug SCSI Drive
Cage Installation Instructions
.
Expansion Boards
To install an expansion board:
1.
Complete the “Preparation Procedures” in this chapter.
2.
From inside the chassis, push the expansion slot cover through the rear of the
chassis.
3.
Depending on the length of the expansion card, do one of the following:
— If the card is full-length, go to step 4.
— If the card is half-length, go to step 5.
HP ProLiant ML330 Generation 3 Server Setup and Installation Guide
4-27