HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 135

Hard Disk

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 135 highlights

Hard Disk Before removing a hard disk, open the system unit. Perform the following steps to remove any of the removable storage devices: NOTICE: To install a second hard disk or replace an existing hard disk, check the SCSI ID of that disk before installing it. See Chapter 3 of this handbook for information on checking SCSI IDs. 1. Unscrew the two captive screws on the left side of the Storage Assembly and pull down the drawer latch on the right side of the Storage Assembly, as shown in Figure 5-48. 1st Captive Screw (2nd Captive screw is below 1st, but not visible in this view) Drawer Ejector Handle Figure 5-48. Removing Storage Drawer from System Unit The Storage Assembly slides partway out of the drawer. 2. Pull the Storage Assembly out as far as it will go. (A safety catch on the left side prevents the drawer from coming all the way out.) 3. Push in on the safety catch and continue pulling the drawer out. Field Replaceable Units 5-53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
Field Replaceable Units
5–53
Hard Disk
Before removing a hard disk, open the system unit.
Perform the following steps to remove any of the removable storage devices:
NOTICE:
To install a second hard disk or replace an existing
hard disk, check the SCSI ID of that disk before
installing it. See Chapter 3 of this handbook for
information on checking SCSI IDs.
1.
Unscrew the two captive screws on the left side of the Storage Assembly and
pull down the drawer latch on the right side of the Storage Assembly, as shown in
Figure 5–48.
1st Captive Screw
(2nd Captive
screw
is below 1st, but
not visible in this
view)
Drawer Ejector
Handle
Figure 5–48.
Removing Storage Drawer from System Unit
The Storage Assembly slides partway out of the drawer.
2.
Pull the Storage Assembly out as far as it will go. (A safety catch on the left side
prevents the drawer from coming all the way out.)
3.
Push in on the safety catch and continue pulling the drawer out.