HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 98

Front Bezel

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Front Bezel This section describes how to remove the J Class front bezel or cover of the system unit. CAUTION: Do not attempt to operate the workstation with the front cover removed. The cover is needed for proper air flow for system cooling. 1. Attach the static-grounding wrist strap by following the instructions on the package. Attach the the sticky end of the wrist strap to bare metal of the system unit. 2. Release the front cover by pushing in the two locking tabs at the front of the system unit as shown in Figure 5-9. Figure 5-9. Opening the System Unit 3. Swing the panel down and pull up slightly so the two guide pins on the bottom clear their guides and lay the front cover down. Reverse this process to replace the J Class front cover. Be sure top latches snap completely into position. 5-16 Field Replaceable Units

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
5–16
Field Replaceable Units
Front Bezel
This section describes how to remove the J Class front bezel or cover of the system
unit.
CAUTION:
Do not
attempt to operate the workstation with the
front cover removed. The cover is needed for proper
air flow for system cooling.
1.
Attach the static-grounding wrist strap by following the instructions on the
package. Attach the the sticky end of the wrist strap to bare metal of the system
unit.
2.
Release the front cover by pushing in the two locking tabs at the front of the sys-
tem unit as shown in Figure 5–9.
Figure 5–9.
Opening the System Unit
3.
Swing the panel down and pull up slightly so the two guide pins on the bottom
clear their guides and lay the front cover down.
Reverse this process to replace the J Class front cover.
Be sure top latches snap completely into position.