HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 136

Removing the Drives from the Storage Assembly

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 136 highlights

4. Set the drawer on a flat surface. 5. Disconnect the SCSI and power cables from the back of the drive. 6. Remove the two screws holding the drive mounting bracket in place and slide the drive and bracket out. See Figure 5-49. PCB side of drive Figure 5-49. Removing the Drives from the Storage Assembly To replace a hard drive, follow these steps: 1. If the drive that's being installed doesn't already have drive brackets attached, do this now, using Figure 5-50 as a guide. Do not over-tighten the screws holding the drive in the storage drawer. 5-54 Field Replaceable Units

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
5–54
Field Replaceable Units
4.
Set the drawer on a flat surface.
5.
Disconnect the SCSI and power cables from the back of the drive.
6.
Remove the two screws holding the drive mounting bracket in place and slide
the drive and bracket out. See Figure 5–49.
PCB side of drive
Figure 5–49.
Removing the Drives from the Storage Assembly
To replace a hard drive, follow these steps:
1.
If the drive that’s being installed doesn’t already have drive brackets attached,
do this now, using Figure 5–50 as a guide.
Do not over-tighten the screws holding the drive in the storage drawer.