Home » Intel Manuals » Processors » Intel Q9400S » Manual Viewer

Intel Q9400S Design Guidelines - Page 94

Thermocouple Placed into Groove, Removing Excess Solder

UPC - 735858207973

Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Figure 49. Thermocouple Placed into Groove Case Temperature Reference Metrology 29. Using a blade carefully shave the excess solder above the IHS surface. Only shave in one direction until solder is flush with the groove surface (see Figure 50). Figure 50. Removing Excess Solder Note: Take usual precautions when using open blades. 30. Clean the surface of the IHS with Alcohol and use compressed air to remove any remaining contaminants. 31. Fill the rest of the groove with Loctite* 498 Adhesive. Verify under the microscope that the thermocouple wire is below the surface along the entire length of the IHS groove (see Figure 51). 94 Thermal and Mechanical Design Guidelines

Section	Page
1 Introduction	11
1.1 Document Goals and Scope	11
1.1.1 Importance of Thermal Management	11
1.1.2 Document Goals	11
1.1.3 Document Scope	12
1.2 References	13
1.3 Definition of Terms	14
2 Processor Thermal/Mechanical Information	17
2.1 Mechanical Requirements	17
2.1.1 Processor Package	17
2.1.2 Heatsink Attach	19
2.1.2.1 General Guidelines	19
2.1.2.2 Heatsink Clip Load Requirement	19
2.1.2.3 Additional Guidelines	20
2.2 Thermal Requirements	20
2.2.1 Processor Case Temperature	20
2.2.2 Thermal Profile	21
2.2.3 TCONTROL	23
2.3 Heatsink Design Considerations	24
2.3.1 Heatsink Size	25
2.3.2 Heatsink Mass	25
2.3.3 Package IHS Flatness	26
2.3.4 Thermal Interface Material	26
2.4 System Thermal Solution Considerations	27
2.4.1 Chassis Thermal Design Capabilities	27
2.4.2 Improving Chassis Thermal Performance	27
2.4.3 Summary	28
2.5 System Integration Considerations	28
3 Thermal Metrology	29
3.1 Characterizing Cooling Performance Requirements	29
3.1.1 Example	31
3.2 Processor Thermal Solution Performance Assessment	31
3.3 Local Ambient Temperature Measurement Guidelines	32
3.4 Processor Case Temperature Measurement Guidelines	34
4 Thermal Management Logic and Thermal Monitor Feature	35
4.1 Processor Power Dissipation	35
4.2 Thermal Monitor Implementation	35
4.2.1 PROCHOT# Signal	36
4.2.2 Thermal Control Circuit	36
4.2.2.1 Thermal Monitor	36
4.2.2.2 Thermal Monitor 2 (TM2)	37
4.2.3 Operation and Configuration	38
4.2.4 On-Demand Mode	39
4.2.5 System Considerations	39
4.2.6 Operating System and Application Software Considerations	40
4.2.7 THERMTRIP# Signal	40
4.2.8 Cooling System Failure Warning	40
4.2.9 Digital Thermal Sensor	41
4.2.10 Platform Environmental Control Interface (PECI)	42
5 Intel® Thermal/Mechanical Reference Design Information	43
5.1 ATX Reference Design Requirements	43
5.2 Validation Results for Reference Design	45
5.2.1 Heatsink Performance	45
5.2.2 Acoustics	46
5.2.3 Altitude	47
5.2.4 Reference Heatsink Thermal Validation	47
5.2.5 Fan Performance for Active Heatsink Thermal Solution	48
5.3 Environmental Reliability Testing	49
5.3.1 Structural Reliability Testing	49
5.3.1.1 Random Vibration Test Procedure	49
5.3.1.2 Shock Test Procedure	49
5.3.2 Power Cycling	51
5.3.3 Recommended BIOS/Processor/Memory Test Procedures	51
5.4 Material and Recycling Requirements	51
5.5 Safety Requirements	52
5.6 Geometric Envelope for Intel® Reference ATX Thermal Mechanical Design	52
5.7 Reference Attach Mechanism	53
5.7.1 Structural Design Strategy	53
5.7.2 Mechanical Interface to the Reference Attach Mechanism	54
6 Intel® Quiet System Technology (Intel® QST)	57
6.1 Intel® Quiet System Technology Algorithm	57
6.1.1 Output Weighting Matrix	58
6.1.2 Proportional-Integral-Derivative (PID)	58
6.2 Board and System Implementation of Intel® Quiet System Technology	60
6.3 Intel® QST Configuration and Tuning	62