JVC GY-HM700UXT 132 page operation manual for the GY-HM700 solid state camcord - Page 119

IEEE1394 Connection, PHONES] Terminal

Get JVC GY-HM700UXT - Prohd Compact Shoulder Solid State Camcorder PDF manuals and user guides View all JVC GY-HM700UXT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

[PHONES] Terminal Audio output from the [PHONES] terminal can be selected using [Audio Monitor] in the [A/V Out] menu (A Page 87) as well as the [MONITOR SELECT] switch on the camera recorder. The different combinations of settings that are output from the [PHONES] terminal and monitor speaker are as follows. [MONITOR SELECT] [Audio Monitor] Switch Settings Settings [CH-1] ^ [BOTH] [Mix] [CH-2] [Stereo] ^ [PHONES] Terminal L R CH1 CH1+CH2 CH1 CH2 CH2 IEEE1394 Connection Note: ● When connecting the camera recorder to an external device using an IEEE1394 cable, make sure to observe the following. Improper connection may cause the circuit of the connected unit to malfunction. ● Turn off the power of the camera recorder and connected devices before connecting the IEEE1394 cable. ● Do not connect the cable in an environment where static electricity occurs or is likely to occur. ● Make sure that each camera recorder is connected to only one external device at any one time. ● Turn off the power of the camera recorder and connected devices before switching the [HD/DV] IEEE1394 terminal mode switch. ● A message indicating AVIDEO FORMAT INCORRECTB appears if the format of the input/output video signals from the [IEEE1394] input terminal is different from the [HD/DV] IEEE1394 terminal mode switch setting. Adjust the [HD/ DV] IEEE394 terminal mode switch according to the video format. Connecting an external device to the IEEE1394 terminal enables you to perform the following. A Backup recording (A Page 116) The images recorded on the SDHC card in the camera recorder can be backed up. B Stream transmission to a non-linear editing system (A Page 117) Playback images on the camera recorder can be stream output during editing using a non-linear editing system. VIDEO FORMAT INCORRECT ● If the [INT/EXT] IEEE1394 interface terminal switch is set at AEXTB and the AHQB mode is selected in [Frame & Bit Rate], signals will not be output from the [IEEE1394] terminal. (A Page 71) [HD/DV] IEEE 1394 Terminal Mode Switch [IEEE1394] Terminal 115

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
115
[PHONES] Terminal
Audio output from the [PHONES] terminal can be selected
using [Audio Monitor] in the [A/V Out] menu (
A
Page 87) as
well as the [MONITOR SELECT] switch on the camera
recorder.
The different combinations of settings that are output from
the [PHONES] terminal and monitor speaker are as follows.
Connecting an external device to the IEEE1
3
94 terminal
enables you to perform the following.
A
Backup recording (
A
Page 116)
The images recorded on the SDHC card in the camera
recorder can be backed up.
B
Stream transmission to a non-linear editing system
(
A
Page 117)
Playback images on the camera recorder can be stream
output during editing using a non-linear editing system.
Note:
●
When connecting the camera recorder to an external
device using an IEEE1
3
94 cable, make sure to observe
the following. Improper connection may cause the circuit
of the connected unit to malfunction.
●
Turn off the power of the camera recorder and
connected devices before connecting the IEEE1
3
94
cable.
●
Do not connect the cable in an environment where
static electricity occurs or is likely to occur.
●
Make sure that each camera recorder is connected to
only one external device at any one time.
●
Turn off the power of the camera recorder and
connected devices before switching the [HD/DV]
IEEE1
3
94 terminal mode switch.
●
A message indicating
A
VIDEO FORMAT INCORRECT
B
appears if the format of the input/output video signals from
the [IEEE1
3
94] input terminal is different from the [HD/DV]
IEEE1
3
94 terminal mode switch setting. Adjust the [HD/
DV] IEEE
3
94 terminal mode switch according to the video
format.
●
If the [INT/EXT] IEEE1
3
94 interface terminal switch is set
at
A
EXT
B
and the
A
HQ
B
mode is selected in [Frame & Bit
Rate], signals will not be output from the [IEEE1
3
94]
terminal. (
A
Page 71)
[MONITOR SELECT]
Switch Settings
[Audio Monitor]
Settings
[PHONES] Terminal
L
R
[CH-1]
^
CH1
[BOTH]
[Mix]
CH1+CH2
[Stereo]
CH1
CH2
[CH-2]
^
CH2
IEEE1
3
94 Connection
[HD/DV] IEEE 1
3
94
Terminal Mode
Switch
[IEEE1
3
94] Terminal
VIDEO FORMAT
INCORRECT