JVC GY-HM700UXT 132 page operation manual for the GY-HM700 solid state camcord - Page 121

Stream Transmission to a Non-linear Editing System, Connect the IEEE1

Get JVC GY-HM700UXT - Prohd Compact Shoulder Solid State Camcorder PDF manuals and user guides View all JVC GY-HM700UXT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

Stream Transmission to a Non-linear Editing System Playback images on the camera recorder can be stream output during editing using a non-linear editing system. Ⅵ Loading to a Non-linear Editing System in Play Mode 1 Perform the following settings on the camera recorder. A Set the [HD/DV] IEEE1394 terminal mode switch to ADVB. B Set the [INT/EXT] IEEE1394 interface terminal switch to AEXTB. Memo: ● Stream transmission is only possible for DV format images. 2 Connect the IEEE1394 cable. 3 Turn on the power of both the camera recorder and non-linear editing system. 4 Set the camera recorder to Media mode. Press the [CAM/MEDIA] selection button to switch to Media mode. (A Page 7) 7 Start loading to the non-linear editing system. For details, refer to the instruction manual of the non-linear editing system. 8 Loading is complete. After loading is complete, press the [CANCEL] button on the camera recorder to stop playback. Memo: ● Switch the [HD/DV] IEEE1394 terminal mode switch only after turning OFF the power of the camera recorder. ● The operating procedures vary depending on the characteristics and specifications of the connected devices, and transfer of data may fail even when the devices are properly connected. ● If noise appears on the screen or audio sound is interrupted, reconnect the IEEE1394 cable or turn on the power of the camera recorder again. ● Noise may occur in the audio when you turn ON/OFF the power of the device connected to the [IEEE1394] terminal. Before performing any of these operations, lower the volume of the device connected to the camera recorder to the minimum. [HD/DV] IEEE 1394 Terminal Mode Switch [INT/EXT] IEEE1394 Interface Terminal Switch IEEE1394 Cable [IEEE1394] Terminal PC Signal Flow Note: ● Start recording only after ensuring that the devices are properly connected. 5 Insert the media to be dubbed. Camera recorder : Recorded SDHC card 6 Press the play button (center of the cross-shaped button) on the camera recorder. Playback starts. 117

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
117
Stream Transmission to a Non-linear
Editing System
Playback images on the camera recorder can be stream
output during editing using a non-linear editing system.
±
Loading to a Non-linear Editing System
in Play Mode
1
Perform the following settings on the camera
recorder.
A
Set the [HD/DV] IEEE1
3
94 terminal mode switch to
A
DV
B
.
B
Set the [INT/EXT] IEEE1
3
94 interface terminal switch to
A
EXT
B
.
Memo:
●
Stream transmission is only possible for DV format
images.
2
Connect the IEEE1
3
94 cable.
3
Turn on the power of both the camera recorder and
non-linear editing system.
4
Set the camera recorder to Media mode.
Press the [CAM/MEDIA] selection button to switch to Media
mode. (
A
Page 7)
Note:
●
Start recording only after ensuring that the devices are
properly connected.
5
Insert the media to be dubbed.
6
Press the play button (center of the cross-shaped
button) on the camera recorder.
Playback starts.
7
Start loading to the non-linear editing system.
For details, refer to the instruction manual of the non-linear
editing system.
8
Loading is complete.
After loading is complete, press the [CANCEL] button on the
camera recorder to stop playback.
Memo:
●
Switch the [HD/DV] IEEE1
3
94 terminal mode switch only
after turning OFF the power of the camera recorder.
●
The operating procedures vary depending on the
characteristics and specifications of the connected
devices, and transfer of data may fail even when the
devices are properly connected.
●
If noise appears on the screen or audio sound is
interrupted, reconnect the IEEE1
3
94 cable or turn on the
power of the camera recorder again.
●
Noise may occur in the audio when you turn ON/OFF the
power of the device connected to the [IEEE1
3
94] terminal.
Before performing any of these operations, lower the
volume of the device connected to the camera recorder to
the minimum.
Camera recorder
: Recorded SDHC card
IEEE1
3
94
Cable
Signal Flow
[HD/DV] IEEE 1
3
94
Terminal Mode
Switch
[IEEE1
3
94] Terminal
PC
[INT/EXT] IEEE1
3
94
Interface Terminal
Switch