JVC GY-HM700UXT 132 page operation manual for the GY-HM700 solid state camcord - Page 45

White Paint Adjustment, Automatic White Balance Mode FAW, Fulltime Auto White balance

Get JVC GY-HM700UXT - Prohd Compact Shoulder Solid State Camcorder PDF manuals and user guides View all JVC GY-HM700UXT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Ⅵ Error message If the white balance adjustment is not correctly completed, one of the following messages will appear for about 5 seconds. Error Message Status NG : OBJECT The object used is defective. Displayed when there is not enough white color on the object, or when the color temperature is not suitable. Use another white object and adjust the white balance again. ERROR : LOW LIGHT Insufficient illumination. Displayed when the lighting is dark. Increase the lighting and adjust the white balance again. ERROR : OVER LIGHT Excessive illumination. Displayed when the lighting is too bright. Decrease the lighting and adjust the white balance again. Ⅵ White Paint Adjustment You can fine-tune the white balance saved in Memory A or Memory B. * Adjust [White Paint R]/[White Paint B] in [Main Menu]B[Camera Process]B[White Balance] (A Page 79) When [AWB] is selected, the normal white paint adjustment value is cleared. However, you can also set to keep the value even when [AWB] is executed. (A Page 79) Automatic White Balance Mode (FAW: Fulltime Auto White balance) You can assign AFAWB (Fulltime Auto White balance) to any of the three positions on the [WHT.BAL] selection switch. Configure the setting with [FAW] in the [Camera Function]B[Switch Set] menu. (A Page 74) Set the [FULL AUTO] switch on the camera recorder to AONB to enter FAW mode. White balance is automatically adjusted according to the color temperature of the lighting on the object. White balance switching with the [WHT.BAL] selection switch is disabled. Memo: ● When [White Balance] in the [Camera Function]B[FULL AUTO] menu is set to ASW SetB, you can switch the white balance with the [WHT.BAL] selection switch on the camera recorder. (A Page 75) Note: ● The accuracy of [FAW] is inferior to that of Auto White Balance. ● When the power of the camera recorder is turned on with the [FAW] mode selected, it takes about 15 seconds for the colors to stabilize. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
41
±
Error message
If the white balance adjustment is not correctly completed,
one of the following messages will appear for about 5
seconds.
±
White Paint Adjustment
You can fine-tune the white balance saved in Memory A or
Memory B.
* Adjust [White Paint R]/[White Paint B] in [Main
Menu]
B
[Camera Process]
B
[White Balance] (
A
Page 79)
When [AWB] is selected, the normal white paint adjustment
value is cleared. However, you can also set to keep the value
even when [AWB] is executed. (
A
Page 79)
Automatic White Balance Mode (FAW:
Fulltime Auto White balance)
You can assign
A
FAW
B
(Fulltime Auto White balance) to any
of the three positions on the [WHT.BAL] selection switch.
Configure the setting with [FAW] in the [Camera
Function]
B
[Switch Set] menu. (
A
Page 74)
Set the [FULL AUTO] switch on the camera recorder to
A
ON
B
to enter FAW mode. White balance is automatically adjusted
according to the color temperature of the lighting on the
object.
White balance switching with the [WHT.BAL] selection switch
is disabled.
Memo:
●
When [White Balance] in the [Camera Function]
B
[FULL
AUTO] menu is set to
A
SW Set
B
, you can switch the white
balance with the [WHT.BAL] selection switch on the
camera recorder. (
A
Page 75)
Note:
●
The accuracy of [FAW] is inferior to that of Auto White
Balance.
●
When the power of the camera recorder is turned on with
the [FAW] mode selected, it takes about 15 seconds for
the colors to stabilize.
Error Message
Status
NG : OBJECT
The object used is defective.
Displayed when there is not enough
white color on the object, or when the
color temperature is not suitable.
Use another white object and adjust
the white balance again.
ERROR : LOW LIGHT
Insufficient illumination.
Displayed when the lighting is dark.
Increase the lighting and adjust the
white balance again.
ERROR : OVER LIGHT
Excessive illumination.
Displayed when the lighting is too
bright. Decrease the lighting and adjust
the white balance again.