JVC GY-HM700UXT 132 page operation manual for the GY-HM700 solid state camcord - Page 120

Backup Recording, Connecting External Devices, Checking Videos Recorded on the, External Device

Get JVC GY-HM700UXT - Prohd Compact Shoulder Solid State Camcorder PDF manuals and user guides View all JVC GY-HM700UXT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 120 highlights

Connecting External Devices IEEE1394 Connection (continued) Backup Recording When the camera recorder is set to Camera mode, images shot using it can be stream output from the IEEE1394 terminal. According to the recording operation on the camera recorder, recording to the camera recorder and external device may be performed synchronously or separately. 1 Connect the camera recorder to the backup device. Connect the camera recorder to the backup device using an IEEE1394 cable, using the camera recorder as the master device. Camera recorder (Master Device) [HD/DV] IEEE 1394 Terminal Mode Switch [INT/EXT] IEEE1394 Interface Terminal Switch IEEE1394 Cable [IEEE1394] Terminal Backup Device Signal Flow 2 Set the camera recorder to Camera mode. 3 Set the recording video format. Note: ● Make sure that the SP mode is selected for the [Frame & Bit Rate] setting. 4 Perform the following settings on the camera recorder (master device). A Set the [HD/DV] IEEE1394 terminal mode switch. [DV] : During backup in the DV format [HD] : During backup in the HD format B Set the [INT/EXT] IEEE1394 interface terminal switch to AEXTB. C Switch to Camera mode. D Specify how recording to the camera recorder and external device is to be performed with the recording operation on the camera recorder using [1394 Rec Trigger] in the [Others] menu. (A Page 88) 5 Set the external device to a mode that enables recording. For setting and operation of external devices, refer to the instruction manual of the respective devices. Note: ● Adjust the camera recorder and external device to the same IEEE1394 settings. ● Start recording only after ensuring that the devices are properly connected. 6 Perform recording using the camera recorder. If the settings in 3 are appropriate, video images will be recorded to the camera recorder and external device. Note: ● Images, audio and time code at the points where recording starts and ends may be out of sync depending on the camera recorder and backup device in use. Memo: ● When backup recording starts, a ATRIGGER TO DVB or ATRIGGER TO HDB message appears on the LCD monitor and viewfinder for about 3 seconds. Ⅵ Checking Videos Recorded on the External Device (IEEE1394 Input mode of Media mode) When images are displayed in thumbnails in Media mode (SD Card mode) and power of the device connected to the [IEEE1394] terminal is turned on, pressing the [CAM/MEDIA] selection button displays the playback images of the connected device on the LCD monitor and viewfinder. Pressing the same button has no effect if the [IEEE1394] connection is not recognized, such as when the power of the device connected to the [IEEE1394] terminal is turned off. Refer to [Status Screen in IEEE1394 Input Mode] (A Page 102 ) for the status display of this mode. 1 Press the [CAM/MEDIA] button to set to the IEEE1394 Input mode. 2 Set the external device to the playback mode. Video images recorded on the external device are displayed on the LCD monitor and viewfinder. Note: ● This mode is used for viewing images input to the [IEEE1394] terminal from an external device, and not intended for recording input images on the camera recorder. 116

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
116
Connecting External Devices
Backup Recording
When the camera recorder is set to Camera mode, images
shot using it can be stream output from the IEEE1
3
94
terminal.
According to the recording operation on the camera recorder,
recording to the camera recorder and external device may be
performed synchronously or separately.
1
Connect the camera recorder to the backup device.
Connect the camera recorder to the backup device using an
IEEE1
3
94 cable, using the camera recorder as the master
device.
2
Set the camera recorder to Camera mode.
3
Set the recording video format.
Note:
●
Make sure that the SP mode is selected for the [Frame &
Bit Rate] setting.
4
Perform the following settings on the camera recorder
(master device).
A
Set the [HD/DV] IEEE1
3
94 terminal mode switch.
B
Set the [INT/EXT] IEEE1
3
94 interface terminal switch to
A
EXT
B
.
C
Switch to Camera mode.
D
Specify how recording to the camera recorder and
external device is to be performed with the recording
operation on the camera recorder using [1
3
94 Rec
Trigger] in the [Others] menu. (
A
Page 88)
5
Set the external device to a mode that enables
recording.
For setting and operation of external devices, refer to the
instruction manual of the respective devices.
Note:
●
Adjust the camera recorder and external device to the
same IEEE1
3
94 settings.
●
Start recording only after ensuring that the devices are
properly connected.
6
Perform recording using the camera recorder.
If the settings in
3
are appropriate, video images will be
recorded to the camera recorder and external device.
Note:
●
Images, audio and time code at the points where
recording starts and ends may be out of sync depending
on the camera recorder and backup device in use.
Memo:
●
When backup recording starts, a
A
TRIGGER TO DV
B
or
A
TRIGGER TO HD
B
message appears on the LCD
monitor and viewfinder for about
3
seconds.
±
Checking Videos Recorded on the
External Device
(IEEE1
3
94 Input mode of Media mode)
When images are displayed in thumbnails in Media mode
(SD Card mode) and power of the device connected to the
[IEEE1
3
94] terminal is turned on, pressing the [CAM/MEDIA]
selection button displays the playback images of the
connected device on the LCD monitor and viewfinder.
Pressing the same button has no effect if the [IEEE1
3
94]
connection is not recognized, such as when the power of the
device connected to the [IEEE1
3
94] terminal is turned off.
Refer to [Status Screen in IEEE1
3
94 Input Mode] (
A
Page
102 ) for the status display of this mode.
1
Press the [CAM/MEDIA] button to set to the IEEE1
3
94
Input mode.
2
Set the external device to the playback mode.
Video images recorded on the external device are displayed
on the LCD monitor and viewfinder.
Note:
●
This mode is used for viewing images input to the
[IEEE1
3
94] terminal from an external device, and not
intended for recording input images on the camera
recorder.
IEEE1
3
94 Connection
(continued)
[DV]
:
During backup in the DV format
[HD]
:
During backup in the HD format
Camera recorder
(Master Device)
Backup Device
IEEE1
3
94
Cable
Signal Flow
[HD/DV] IEEE 1
3
94
Terminal Mode Switch
[IEEE1
3
94]
Terminal
[INT/EXT] IEEE1
3
94
Interface Terminal
Switch