Kyocera FS-6525MFP Kyocera Command Center RX User Guide Rev-1.60 - Page 59

Advanced > Protocols > TCP/IP > Logical Printers, IP Filters IPv6, IP Address IPv6, Prefix Length

Get Kyocera FS-6525MFP PDF manuals and user guides View all Kyocera FS-6525MFP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Settings Pages To allow access to a network, enter the network IPv4 address, and the subnet mask. For example: To allow access from all hosts on network 192, enter "192.0.0.0" for the IP address, and "255.0.0.0" for the subnet mask. Subnet mask can also be left blank. To allow access to a single IP address, enter the IPv4 address, and "255.255.255.255" for the subnet mask. • Protocols Specifies the protocol to be permitted. The following protocols can be selected: • LPD • FTP • IPP • ThinPrint • HTTP • Raw • SNMP • IPP over SSL • HTTPS IP Filters (IPv6) • IP Address (IPv6) Specifies the IP addresses to which access is granted. When there are no entries, access is allowed to all. The number of addresses that can be specified depends on the IPv6 network address along with the prefix length setting. To filter a single IPv6 address: Enter the desired IPv6 address, along with a prefix length of 128. • Prefix Length Specifies the IPv6 prefix length. It can be a decimal value between 0 and 128. • Protocols Specifies the protocols through which access is granted. The following protocols can be selected. • LPD • FTP • IPP • ThinPrint • HTTP • Raw • SNMP • IPP over SSL • HTTPS Advanced > Protocols > TCP/IP > Logical Printers This page allows you to configure the Logical Printers. This machine can be used as a virtual printer for converting ASCII print data to PostScript data or for adding and/or replacing character strings (commands) at the beginning or end of job data. Up to four logical printers can be set. COMMAND CENTER RX 6-35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Settings Pages
To allow access to a network, enter the network IPv4 address, and the
subnet mask. For example: To allow access from all hosts on network 192,
enter "192.0.0.0" for the IP address, and "255.0.0.0" for the subnet
mask. Subnet mask can also be left blank.
To allow access to a single IP address, enter the IPv4 address, and
"255.255.255.255" for the subnet mask.
•
Protocols
Specifies the protocol to be permitted. The following protocols can be
selected:
•
LPD
•
FTP
•
IPP
•
ThinPrint
•
HTTP
•
Raw
•
SNMP
•
IPP over SSL
•
HTTPS
IP Filters (IPv6)
•
IP Address (IPv6)
Specifies the IP addresses to which access is granted. When there are no
entries, access is allowed to all. The number of addresses that can be
specified depends on the IPv6 network address along with the prefix length
setting. To filter a single IPv6 address: Enter the desired IPv6 address, along
with a prefix length of 128.
•
Prefix Length
Specifies the IPv6 prefix length. It can be a decimal value between 0 and 128.
•
Protocols
Specifies the protocols through which access is granted. The following
protocols can be selected.
•
LPD
•
FTP
•
IPP
•
ThinPrint
•
HTTP
•
Raw
•
SNMP
•
IPP over SSL
•
HTTPS
Advanced > Protocols > TCP/IP > Logical Printers
This page allows you to configure the Logical Printers. This machine can be
used as a virtual printer for converting ASCII print data to PostScript data or for
adding and/or replacing character strings (commands) at the beginning or end
of job data. Up to four logical printers can be set.
COMMAND CENTER RX
6-35