Kyocera FS-6525MFP Kyocera Command Center RX User Guide Rev-1.60 - Page 67

Advanced > Management > SNMP > SNMPv3, Basic > Defaults > Device Defaults

Get Kyocera FS-6525MFP PDF manuals and user guides View all Kyocera FS-6525MFP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Settings Pages sysLocation The MIB-II sysLocation object. Usually this is the location information of the printing system which is described under Device Defaults. To change location, go to Location in Basic > Defaults > Device Defaults. HP Web Jetadmin Compatibility Turns HP Web Jetadmin Compatibility On or Off. After you have changed the setting, you must restart the printing system. Authentication Traps Specifies whether to use authentication traps. If enabled (On), an SNMP trap is generated when an attempt to read or write is made using an incorrect community name. The trap is sent to the configured trap address. After you have changed the setting, you must restart the printing system. Trap Community The SNMP trap community name to be used when the printing system generates a trap. Trap IP Address (IPv4) Enter the IPv4 address that receives traps. Select On to enable trap receiving. Trap IP Address (IPv6) Enter the IPv6 address that receives traps. Select On to enable trap receiving. Trap IPX Address Enter the IPX address that receives traps. Select On to enable trap receiving. Selected Errors Select the events which will cause a trap to be generated from Add Paper, Low Toner, Add Toner, Cover Open, Paper Jam, and All Other Errors. Advanced > Management > SNMP > SNMPv3 The section below provides a summary of the items displayed on the SNMPv3 page. After you have changed the setting, you must restart the printing system. SNMPv3 Sets whether to use the SNMPv3 protocol. Set On to use it. Authentication Sets whether to authenticate the user in SNMP communication. Hash Selects the hash algorithm. This item is displayed when the Authentication is On. Privacy Sets whether to encrypt the communicated data in SNMP communication. This becomes available when Authentication is enabled. Encryption Selects the encryption algorithm. This item is displayed when Privacy is On. User Name Enter the name of the read-only user. Password COMMAND CENTER RX 6-43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Settings Pages
sysLocation
The MIB-II sysLocation object. Usually this is the location information of the
printing system which is described under
Device Defaults
. To change
location, go to
Location
in
Basic > Defaults > Device Defaults
.
HP Web Jetadmin Compatibility
Turns HP Web Jetadmin Compatibility
On
or
Off
. After you have changed
the setting, you must restart the printing system.
Authentication Traps
Specifies whether to use authentication traps. If enabled (
On
), an SNMP trap
is generated when an attempt to read or write is made using an incorrect
community name. The trap is sent to the configured trap address. After you
have changed the setting, you must restart the printing system.
Trap Community
The SNMP trap community name to be used when the printing system
generates a trap.
Trap IP Address (IPv4)
Enter the IPv4 address that receives traps. Select
On
to enable trap
receiving.
Trap IP Address (IPv6)
Enter the IPv6 address that receives traps. Select
On
to enable trap
receiving.
Trap IPX Address
Enter the IPX address that receives traps. Select
On
to enable trap
receiving.
Selected Errors
Select the events which will cause a trap to be generated from
Add Paper
,
Low Toner
,
Add Toner
,
Cover Open
,
Paper Jam
, and
All Other Errors
.
Advanced > Management > SNMP > SNMPv3
The section below provides a summary of the items displayed on the
SNMPv3
page. After you have changed the setting, you must restart the printing system.
SNMPv3
Sets whether to use the SNMPv3 protocol. Set
On
to use it.
Authentication
Sets whether to authenticate the user in SNMP communication.
Hash
Selects the hash algorithm. This item is displayed when the
Authentication
is
On
.
Privacy
Sets whether to encrypt the communicated data in SNMP communication.
This becomes available when
Authentication
is enabled.
Encryption
Selects the encryption algorithm. This item is displayed when
Privacy
is
On
.
User Name
Enter the name of the read-only user.
Password
COMMAND CENTER RX
6-43