LG 40LV570H INSTALLATION - Page 31
SAP MENU EN 2nd Audio Program, DEF. ASP. RATIO Default Aspect Ratio, AUDIO OUTPUT, PRO:CENTRIC, BACK
View all LG 40LV570H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 31 highlights
Installer Menu (Cont.) • 6 = Scaler Model RJPs: DVI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard. Note: See also Reference section, "RJP Model List & Input Autosensing Hierarchy." Settings 1, 2, 5, and 6 allow the lodge staff to customize each TV's RJP setup based on customer requirements. Note: When this item is enabled in the Installer Menu, item 042 AUTO INPUTS is automatically set to 0. 094 - SAP MENU EN (2nd Audio Program) Set to 1 to enable the SAP feature in the Function Menu, when the Function Menu is available (i.e., TV is not in Pass-through Mode). Set to 0 to disable the SAP feature in the Function Menu, when the Function Menu is available. 096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up: 0 = Set By Program 2 = 16:9 (default) 4 = Zoom 1 = 4:3 3 = Just Scan Note: This item is not available in the Installer Menu unless item 106 ASP RATIO LOCK is set to 0. 097 - AUDIO OUTPUT Determines availability and signal type/level (fixed speaker, variable speaker, or fixed line level [amplifier]) of the audio output to be used by external audio equipment connected to the SPEAKER OUT / LINE OUT jack on the TV. Set to 0 to disable audio output. Otherwise, see the table below and set as required in accordance with audio equipment. See also Reference section, "External Stereo Speaker Specifications." Speaker Output Line Output Value 1 2 3 4 5 6 7 8 9 Status Fixed 0.01 Watts Fixed 0.03 Watts Fixed 0.05 Watts Fixed 0.10 Watts Fixed 0.20 Watts Fixed 0.50 Watts Fixed 1.00 Watt (default) Control with volume Fixed line level (typically 400 mVrms ± 100 mVrms @10KΩ) output 098 - PRO:CENTRIC Selects the Pro:Centric Application Mode. Set to 0 (default) to disable the Pro:Centric application. Set to 1 for Flash Mode. Set to 2 for GEM (Java Application) Mode. The TV must be turned OFF for a few seconds to initiate the Pro:Centric application download. When the TV is turned back ON, it may take several minutes to load the Pro:Centric application after the initial download. Note: This item is not available in the Installer Menu when item 119 DATA CHANNEL is set to 0. 099 - BACK LIGHTING Sets the TV screen brightness at power up. Default setting is 255. • 1 (dimmest picture) - 100 (brightest picture) Static Back Lighting • 101 (dimmest picture) - 200 (brightest picture) Dynamic Back Lighting: The TV automatically controls back lighting depending upon the picture level of the current program. • 201 Automatic Static Back Lighting: The TV automatically controls back lighting by using Intelligent Sensor to detect the level of ambient lighting. • 202 Automatic Dynamic Back Lighting: The TV automatically controls back lighting by using Intelligent Sensor to detect the level of ambient lighting and depending upon the picture level of the current program. If set to 201 or 202, back lighting can be controlled via the Picture settings in the TV setup menus. However, each time the TV is turned ON, Picture Mode (set in Picture Menu) is defaulted to Intelligent Sensor. If Picture Mode is manually set to a static option (Vivid, Standard, etc.) during a viewing session, Intelligent Sensor is temporarily disabled. If set to 255, back lighting is controlled via the Picture settings in the TV's setup menus. 102 - ATSC BAND Sets up TV to receive different types of incoming signals. 0 = Broadcast 3 = IRC 1 = CATV 4 = Same as NTSC 2 = HRC 103 - ATSC TUNE MODE Sets ATSC tuning mode. Default set to 1 for Physical Channel scan. Set to 0 for Virtual Channel scan. 104 - START MINOR CHANNEL Sets Minor Start Channel number at power up. 0 = NTSC. If not 0, number selected is the digital channel's Minor Start Channel number. Note: This item is not available in the Installer Menu when item 004 STRT CHANNEL is set to 0 or 255. 206-4317 Draft A.2 31