Netgear WNR1000v3 User Manual - Page 113

The Push 'N' Connect WPS push-button blinks after setting WPS security.

Get Netgear WNR1000v3 - Wireless- N Router PDF manuals and user guides View all Netgear WNR1000v3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

Wireless-N 150 Router WNR1000v3 User Manual The Power light stays amber. When the router is turned on, the Power light turns amber for about 20 seconds and then turns green. If the light does not turn green, the router has a problem. If the Power light is still amber 1 minute after turning on power to the router: 1. Turn the power off and back on to see if the router recovers. 2. Clear the router's configuration to factory defaults. This will set the router's IP address to www.routerlogin.net. This procedure is explained in "Restoring the Default Configuration and Password" on page 7-12. If the error persists, you might have a hardware problem and should contact Technical Support. The Internet light stays amber. When the router is turned on, the Internet light turns amber for about 20 seconds and then turns green. If the light does not turn green, the router has a problem. If the Internet light is still amber 1 minute after turning on power to the router: 1. The Internet is not accessible. Confirm that you have the correct internet setting. 2. Clear the router's configuration to factory defaults. This will set the router's IP address to www.routerlogin.net. This procedure is explained in "Restoring the Default Configuration and Password" on page 7-12. 3. Turn the power off and back on, and re-configure the router, to see if the router recovers. The Internet or LAN port lights are not on. If either the LAN or Internet lights do not light when the Ethernet connection is made, check the following: 1. Make sure that the Ethernet cable connections are secure at the router and at the computer. 2. Make sure that power is turned on to the connected computer. 3. Be sure you are using Ethernet cables like the cable that was supplied with the wireless router. See the NETGEAR Wireless Router Setup Manual for instructions. The Push 'N' Connect (WPS) push-button blinks after setting WPS security. If after using the WPS function the push-button blinks, check the following: 1. Make sure that you are using the push-button (see "Using Push 'N' Connect (Wi-Fi Protected Setup)" on page 2-13). Troubleshooting 7-4 v1.0, February 2010

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Wireless-N 150 Router WNR1000v3 User Manual
Troubleshooting
7-4
v1.0, February 2010
The Power light stays amber.
When the router is turned on, the Power light turns amber for about 20 seconds and then turns
green. If the light does not turn green, the router has a problem.
If the Power light is still amber 1 minute after turning on power to the router:
1.
Turn the power off and back on to see if the router recovers.
2.
Clear the router’s configuration to factory defaults. This will set the router’s IP address to
www.routerlogin.net. This procedure is explained in
“Restoring the Default Configuration and
Password” on page 7-12
.
If the error persists, you might have a hardware problem and should contact Technical Support.
The Internet light stays amber.
When the router is turned on, the Internet light turns amber for about 20 seconds and then turns
green. If the light does not turn green, the router has a problem.
If the Internet light is still amber 1 minute after turning on power to the router:
1.
The Internet is not accessible. Confirm that you have the correct internet setting.
2.
Clear the router’s configuration to factory defaults. This will set the router’s IP address to
www.routerlogin.net. This procedure is explained in
“Restoring the Default Configuration and
Password” on page 7-12
.
3.
Turn the power off and back on, and re-configure the router, to see if the router recovers.
The Internet or LAN port lights are not on.
If either the LAN or Internet lights do not light when the Ethernet connection is made, check the
following:
1.
Make sure that the Ethernet cable connections are secure at the router and at the computer.
2.
Make sure that power is turned on to the connected computer.
3.
Be sure you are using Ethernet cables like the cable that was supplied with the wireless router.
See the
NETGEAR Wireless Router Setup Manual
for instructions.
The Push 'N' Connect (WPS) push-button blinks after setting WPS security.
If after using the WPS function the push-button blinks, check the following:
1.
Make sure that you are using the push-button (see
“Using Push 'N' Connect (Wi-Fi Protected
Setup)” on page 2-13
).