Oki ML591 Troy Etherwind 802.11b Print Server Users Guide - Page 19

Boot Method to, If you are using a Macintosh, no further configuration should be necessary.

Get Oki ML591 PDF manuals and user guides View all Oki ML591 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

• If your network uses WEP encryption, you will need to enable WEP and enter the appropriate WEP key(s). Contact your system manager to determine what information . • If you are using TCP/IP (recommended for Windows printing) and you do not have a DHCP server (see note below), you will need to manually assign a valid IP Address, Subnet Mask, and Gateway and then set the Boot Method to Static. • If you are using a Macintosh, no further configuration should be necessary. When you are done configuring, click OK. For a Glossary of Terms used for all the settings in WP-Admin, see chapter 11. Note: If you are using DHCP on your network, the EtherWind may have acquired valid IP settings at this point and no further configuration is necessary. This might work well if your DHCP server allows the print server to keep this address permanently, but in most cases, you will want to use a static address outside the range reserved for DHCP (See your DHCP server documentation for details). This is because when you configure your printer port, it will go to a static IP address. Your Print Server should be configured correctly at this point. Configuring the EtherWind to print under various operating systems is covered in chapters 4 through 9. 2-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
•
If your network uses WEP encryption, you will need to enable WEP and
enter the appropriate WEP key(s).
Contact your system manager to deter-
mine what information .
•
If you are using TCP/IP (recommended for Windows printing) and you
do not have a DHCP server (see note below), you will need to manually
assign a valid IP Address, Subnet Mask, and Gateway and then set the
Boot Method to
Static
.
•
If you are using a Macintosh, no further configuration should be necessary.
When you are done configuring, click
OK
.
For a Glossary of Terms used for all the settings in WP-Admin, see chapter 11.
Note:
If you are using DHCP on your network, the EtherWind may have acquired
valid IP settings at this point and no further configuration is necessary. This
might work well if your DHCP server allows the print server to keep this
address permanently, but in most cases, you will want to use a static
address outside the range reserved for DHCP (See your DHCP server docu-
mentation for details). This is because when you configure your printer port,
it will go to a static IP address.
Your Print Server should be configured correctly at this point. Configuring the
EtherWind to print under various operating systems is covered in chapters 4
through 9.
2-5