Tripp Lite SU1500XLCD Owner's Manual for On-Line Tower LCD UPS 933168 - Page 21

Ups Setup Overview

Get Tripp Lite SU1500XLCD PDF manuals and user guides View all Tripp Lite SU1500XLCD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Operation UPS SETUP OVERVIEW Your UPS supports a variety of advanced configuration options that can be set up via the front panel LCD screen interface. Some external battery configurations will require the use of External Battery Configuration Software and a RS232 connection to the UPS. PowerAlert UPS monitoring software can also be used to access many advanced configuration options through the use of a direct USB, RS232 or SNMPWEBCARD connection (skip past the LCD set-up instructions for advanced configuration options using PowerAlert). 1. USING THE LCD INTERFACE This UPS supports a variety of user setup options and custom configurations that can be accessed via the front panel LCD screen. Configuration and information items include. 1. Output Voltage 2. Output Frequency 3. Frequency Converter/Regulation 4. Bypass range 5. Economy Mode 6. Audible Alarm 7. Overload Alarm 8. External Batt. 9. IP address To access the UPS SETUP MENU, press the SETUP BUTTON for approximately 3 seconds and release. To gain access to all configuration items, Turn off connected equipment and set the UPS to STANDBY MODE (the UPS is in STANDBY mode when the 3 character LCD display reads "OFF"). Many LCD configuration items cannot be changed in ON LINE, ON BATTERY, ECONOMY or FREQUENCY REGULATION/CONVERTER modes. If a non-supported configuration item is attempted during these modes, the LCD will report "no" to confirm the selection is not available in the current operating mode. Once your configuration settings are complete, EXIT the SETUP MENU by pressing and holding the SETUP BUTTON for approximately 3 seconds. UPS Set-up Using the LCD Screen To access the UPS SETUP MENU, press the front panel SETUP BUTTON for approximately 3 seconds and release. 1 The OUTPUT VOLTAGE selection screen will appear. The last selected UPS OUTPUT voltage setting will appear. If this is your first time running the SETUP MENU, the factory default setting of 120V will be shown. OUTPUT VOLTAGE refers to the nominal output voltage of the UPS. This value is most commonly set to match the prevailing country or region-specific nominal voltage. In general, use 120V for USA and Canada, 127V for Mexico and 100V for Japan. Additional values of 110 & 115V are also available. Note: Certain voltage settings will cause automatic de-rating. See specifications on unit label for de-rating info. ACCEPT AND ADVANCE To ACCEPT the current value & ADVANCE to the next configuration screen , press the ON/SELECT button (less than 1 second). VIEW ALTERNATE SETTINGS To VIEW ALTERNATE SETTINGS, press the SETUP BUTTON repeatedly (under 1 second each). AVAILABLE VALUES* 120V (factory), 127V, 100V, 110V, 115V LEAVE UPS SETUP MODE To leave UPS setup mode, PRESS and HOLD the SETUP BUTTON (about 3 seconds). NOTE - the UPS must be in STANDBY MODE to change the output voltage setting * The currently selected value will show as solid. Alternate values will flash and then remain solid once selected. 21 13-03-138 93-3168-EN.indd 21 3/28/2013 1:05:35 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
21
Operation
UPS SETUP OVERVIEW
Your UPS supports a variety of advanced configuration options that can be set up via the front panel LCD screen interface. Some external
battery configurations will require the use of External Battery Configuration Software and a RS232 connection to the UPS.
PowerAlert
UPS monitoring software can also be used to access many advanced configuration options through the use of a direct USB, RS232 or
SNMPWEBCARD connection (skip past the LCD set-up instructions for advanced configuration options using PowerAlert).
1. USING THE LCD INTERFACE
This UPS supports a variety of user setup options and custom configurations that can be accessed via the front panel LCD screen.
Configuration and information items include.
1. Output Voltage
2. Output Frequency
3. Frequency Converter/Regulation
4. Bypass range
5. Economy Mode
6. Audible Alarm
7. Overload Alarm
8. External Batt.
9. IP address
To access the UPS SETUP MENU, press the SETUP BUTTON for approximately 3 seconds and release.
To gain access to all configuration items, Turn off connected equipment and set the UPS to STANDBY MODE (the UPS is in STANDBY mode
when the 3 character LCD display reads “OFF”).
Many LCD configuration items cannot be changed in ON LINE, ON BATTERY, ECONOMY or FREQUENCY REGULATION/CONVERTER modes.
If a non-supported configuration item is attempted during these modes, the LCD will report “no” to confirm the selection is not available in
the current operating mode.
Once your configuration settings are complete, EXIT the SETUP MENU by pressing and holding the SETUP BUTTON for approximately 3 seconds.
UPS Set-up Using the LCD Screen
To access the UPS SETUP MENU, press the front panel SETUP BUTTON for approximately 3 seconds and release.
1
The OUTPUT VOLTAGE selection screen will appear.
The last selected UPS OUTPUT voltage setting will appear.
If this is your first
time running the SETUP MENU, the factory default setting of 120V will be shown.
OUTPUT VOLTAGE refers to the nominal output voltage of the UPS. This value is most
commonly set to match the prevailing country or region-specific nominal voltage. In general,
use 120V for USA and Canada, 127V for Mexico and 100V for Japan. Additional values of
110 & 115V are also available.
Note: Certain voltage settings will cause automatic de-rating.
See specifications on unit label for de-rating info.
ACCEPT AND ADVANCE
VIEW ALTERNATE SETTINGS
LEAVE UPS SETUP MODE
To ACCEPT the current value
&
ADVANCE
to
the
next
configuration screen , press
the
ON/SELECT button (less
than 1 second).
To VIEW ALTERNATE SETTINGS,
press the SETUP BUTTON
repeatedly
(under
1 second
each).
AVAILABLE VALUES*
120V (factory), 127V,
100V, 110V, 115V
To
leave UPS setup mode,
PRESS and HOLD the SETUP
BUTTON (about 3 seconds).
NOTE - the UPS must be in STANDBY MODE
to change the output voltage setting
* The currently selected value will show as solid. Alternate values will flash and then remain solid once selected.
13-03-138 93-3168-EN.indd
21
3/28/2013
1:05:35 PM