Xerox 6180N DocuSP 61xx version 3.6 - Operator Guide - Page 45

Positioning the stack, Adding paper to trays 3, 4, or 5

Get Xerox 6180N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205425307
View all Xerox 6180N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Figure 5-2. Positioning the stack Routine maintenance For stock outside the recommended limits, refer to the "Technical information" chapter in this guide. 8. Move the rear guide forward until it touches the edge of the stack. 9. Lower the feed belt. 10. Close the tray slowly, but firmly, until it latches. Adding paper to trays 3, 4, or 5 Paper tray 3 or 5 is used to supply the largest volume of paper required for your jobs. These trays can also be used to supply oversized paper for special jobs. Paper in tray 4 is only used for post-process insertion. These trays lower one ream at a time as paper is added. More than one ream can be loaded by pressing the Tray unlock button again after the tray is fully opened. The following steps must be performed to add paper to tray 3, 4 or 5. 1. Press the Tray unlock button on the front of the tray. Wait for the red "Please wait" light to go off. NOTE: If the tray is not pulled out all of the way, the tray elevator will not go down as paper is added. DocuTech 61xx Operator Guide 5-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Routine maintenance
DocuTech 61xx Operator Guide
5-3
Figure 5-2. Positioning the stack
For stock outside the recommended limits, refer to the
"Technical information" chapter in this guide.
8.
Move the rear guide forward until it touches the edge of the
stack.
9.
Lower the feed belt.
10.Close the tray slowly, but firmly, until it latches.
Adding paper to trays 3, 4, or 5
Paper tray 3 or 5 is used to supply the largest volume of paper
required for your jobs. These trays can also be used to supply
oversized paper for special jobs.
Paper in tray 4 is only used for
post-process insertion.
These trays lower one ream at a time as paper is added. More
than one ream can be loaded by pressing the Tray unlock button
again after the tray is fully opened.
The following steps must be performed to add paper to tray 3, 4
or 5.
1.
Press the Tray unlock button on the front of the tray. Wait for
the red "Please wait" light to go off.
NOTE:
If the tray is not pulled out all of the way, the tray
elevator will not go down as paper is added.