Xerox 6180N DocuSP 61xx version 3.6 - Operator Guide - Page 98

Clearing a stitcher spool A fault

Get Xerox 6180N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205425307
View all Xerox 6180N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Problem solving WARNING The binder tape adhesive is hot, approximately 425°F (218°C). Allow the binder to cool for 5 minutes with the finisher doors and top cover open before touching the binder tape. 7. If area 18 is not displayed, proceed to step 10. 8. If area 18 is displayed and the entire binder tape length is not aligned with the tape feeder assembly, stop and follow the WARNING. Proceed to step 10. 9. If area 18 is displayed and the entire binder tape length is aligned with the tape feeder assembly, proceed to step 10. 10. Remove the binder tape. 11. Ensure that area 18 is clear of all binder tape adhesive. If it is not, clean the binder using the procedure, "Cleaning the binder," in the "Routine maintenance" chapter. 12. Close the finisher doors. 13. Close the top cover. Clearing a stitcher spool A fault Repeated jams in area 17 may be caused by the following problems: • Stitcher wire not feeding properly • A kink in the stitcher wire 1. Open the finisher doors. 2. Lift the stitcher panel, which is located directly above the stitcher spools. NOTE: If the spool is empty, replace the stitcher spool A using the procedure, "Replacing the stitcher spool A," in the "Routine maintenance" chapter. 3. Ensure that there is wire on the spool. 4. Pull the green stitcher head release handle forward and up until it latches into place, as shown in figure 6-1. 6-10 DocuTech 61xx Operator Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Problem solving
6-10
DocuTech 61xx Operator Guide
WARNING
The binder tape adhesive is hot, approximately 425°F
(218°C).
Allow the binder to cool for 5 minutes with the
finisher doors and top cover open before touching the
binder tape.
7.
If area 18 is not displayed, proceed to step 10.
8.
If area 18 is displayed and the entire binder tape length is not
aligned with the tape feeder assembly, stop and follow the
WARNING. Proceed to step 10.
9.
If area 18 is displayed and the entire binder tape length is
aligned with the tape feeder assembly, proceed to step 10.
10.Remove the binder tape.
11. Ensure that area 18 is clear of all binder tape adhesive.
If it is
not, clean the binder using the procedure, "Cleaning the
binder," in the "Routine maintenance" chapter.
12.Close the finisher doors.
13.Close the top cover.
Clearing a stitcher spool A fault
Repeated jams in area 17 may be caused by the following
problems:
•
Stitcher wire not feeding properly
•
A kink in the stitcher wire
1.
Open the finisher doors.
2.
Lift the stitcher panel, which is located directly above the
stitcher spools.
NOTE:
If the spool is empty, replace the stitcher spool A using
the procedure, "Replacing the stitcher spool A," in the "Routine
maintenance" chapter.
3.
Ensure that there is wire on the spool.
4.
Pull the green stitcher head release handle forward and up
until it latches into place, as shown in figure 6-1.