Yamaha RX-Z11 Owner's Manual - Page 126

Remote control features Programming codes from other remote controls (LEARN) You can program remote control codes from other remote controls. Use the learning feature if you want to program functions not included in the basic operations covered by the remote control codes, or an appropriate remote control code is not available. You can program the function of other remote control to the buttons in the highlighted areas in the following illustration. The buttons can be programmed independently for each control area. POWER POWER STANDBY POWER TV AV MULTI BD HD DVD CBL SAT TUNER V-AUX DVD DTV DOCK PHONO CD DVR NET USB MD TAPE CD-R VCR XM AMP TV SOURCE SELECT SETUP ID MACRO MODE ZONE SYSTEM MEMORY 1 2 3 4 LEVEL TITLE BAND SRCH MODE VOLUME PRESET/CH MENU ENTER CAT. A-E RETURN MEMORY PC/MCX REC NET RADIO USB DISPLAY MUTE PRG SELECT CLASSICAL 1 CLASSICAL 2 LIVE/CLUB ENTERTAIN 1 2 3 4 MOVIE 5 STEREO ENHANCER SUR. DECODE 6 7 8 THX STRAIGHT PURE DIRECT EXTD SUR. 9 0 10 ENT. PARTY TV VOL SLEEP TV CH HDMI OUT MUTE TV INPUT AUDIO SEL AUDIO 3D DSP Set to SOURCE (U.S.A. and Canada models) Notes • The remote control transmits infrared rays. If the other remote control also uses infrared rays, this remote control can learn most of its functions. However, you may not be able to program some special signals or extremely long transmissions. Refer to the operating instructions for the other remote control. • You cannot program the desired remote control code even if you select the buttons in the highlighted area in the above illustration depending on the selected control area and the assigned library. 1 Set the operation mode selector to FSOURCE and then press an input selector button (3) to select the desired control area. The name of the control area you want to customize appears in the display window (4) on the remote control. DVD y • You can also select the desired control area by pressing 5SELECT l / h repeatedly. • If you want to select "TV", set the operation mode selector to FTV. Note Make sure that the operation mode selector is set to FSOURCE or FTV. When you set the operation mode selector to FAMP and program a remote control codes from other remote controls, the programmed key cannot operate the amplifier function of this unit. 2 Press GSETUP using a ballpoint pen or similar object. "SETUP" appears in the display window (4). SETUP 3 Press 9k / n repeatedly to select "LEARN" and then press 9ENTER. The remote control enters the learning mode. "LEARN" and the name of the selected control area appears in the display window (4) alternately. START DVD 4 Place this remote control about 5 to 10 cm (2 to 4 in) apart from the other remote control on a flat surface so that their infrared transmitters are aimed at each other and then press 9ENTER. "L-KEY" appears in the display window (4). Other remote control POWER POWER STANDBY POWER TV MULTI BD HD DVD CBL SAT TUNER 1 LEVEL TITLE BAND RETURN MEMORY SELECT AV V-AUX DVD DTV DOCK PHONO CD DVR NET USB SETUP ID MACRO MODE ZONE SYSTEM MEMORY 2 3 SRCH MODE VOLUME PRESET/CH MENU ENTER CAT. A-E DISPLAY MUTE MD TAPE CD-R VCR XM AMP TV SOURCE 4 (U.S.A. and Canada models) 5 to 10 cm (2 to 4 in) L-KEY 5 Press the button for which you want to program the new function. "START" appears in the display window (4). POWER POWER STANDBY POWER TV MULTI BD HD DVD CBL SAT TUNER 1 LEVEL TITLE BAND RETURN MEMORY SELECT AV V-AUX DVD DTV DOCK PHONO CD DVR NET USB SETUP ID MACRO MODE ZONE SYSTEM MEMORY 2 3 SRCH MODE VOLUME PRESET/CH MENU ENTER DISPLAY CAT. A-E MD TAPE CD-R VCR XM AMP TV SOURCE 4 (U.S.A. and Canada models) START 126 En