iRobot Roomba 570 Service Manual - Page 32

Roomba Wireless Command Center Base robot 3.4 and 3.5 only - 9 beeps

Get iRobot Roomba 570 PDF manuals and user guides View all iRobot Roomba 570 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Roomba Wireless Command Center (Base robot 3.4 and 3.5 only) The Wireless Command Center allows a user to remotely turn the Roomba on or off, be directed and scheduled. To schedule a Roomba to clean, use the buttons on the Wireless Command Center as if they were on the robot user panel itself. Wireless Command Center Troubleshooting The WCC should work normally at distances of about 30 feet. However, depending on the environment this will vary. In open areas it may be more and when environment cluttered with interfering objects (especially metallic) it will be reduced. Prior to using a new Wireless Command Center (WCC) with Roomba, it needs to be paired to the Roomba. • Remove WCC batteries • Reinstall WCC batteries while holding down the left drive button. • Continue holding the left drive button for 3 seconds or until the days of the week lights flash in a sequence from Saturday to Sunday. • Install WCC battery door. • Hold the WCC close to the robot you want to pair it with. It should stop scrolling. • When the Roomba responds to the WCC, press and hold the DAY and MINUTE buttons for 2 seconds until the WCC lights flash and the Roomba beeps once quickly. • They are now paired. From now on, the when the WCC is powered on, lights will sequence from Sunday to Saturday until the robot is under control. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
32
Roomba Wireless Command Center (Base robot 3.4 and 3.5 only)
The Wireless Command Center allows a user to remotely turn the Roomba on or off, be directed and
scheduled. To schedule a Roomba to clean, use the buttons on the Wireless Command Center as if
they were on the robot user panel itself.
Wireless Command Center Troubleshooting
The WCC should work normally at distances of about 30 feet. However, depending on the
environment this will vary. In open areas it may be more and when environment cluttered with
interfering objects (especially metallic) it will be reduced.
Prior to using a new Wireless Command Center (WCC) with Roomba, it needs to be paired to the
Roomba.
•
Remove WCC batteries
•
Reinstall WCC batteries while holding down the left drive button.
•
Continue holding the left drive button for 3 seconds or until the days of the week lights
flash in a sequence from Saturday to Sunday.
•
Install WCC battery door.
•
Hold the WCC close to the robot you want to pair it with. It should stop scrolling.
•
When the Roomba responds to the WCC, press and hold the DAY and MINUTE buttons
for 2 seconds until the WCC lights flash and the Roomba beeps once quickly.
•
They are now paired. From now on, the when the WCC is powered on, lights will sequence
from Sunday to Saturday until the robot is under control.