Home » Autodesk Manuals » Computer Software » Autodesk 057A1-05A111-1001 » Manual Viewer

Autodesk 057A1-05A111-1001 Getting Started Guide - Page 110

Create the top view, Layer Properties Manager.

UPC - 606122219674

View all Autodesk 057A1-05A111-1001 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

7 Use the Mirror command to mirror the arc using the center points of the left and right circles to define the mirror line. Again, use SHIFT and right-click to access the object snap menu. There are often alternative methods for each step. For example, to create the lower arc, you could have used the Fillet command to fillet the two outer circles with a radius of 250 mm. 8 Trim the outer-left circle as shown. The front view of the part is complete. Next, you will use the objects in the front view to create the top view of the part. Create the top view 1 Set the current layer to Model-Top. You can use the Layer control on the Layers toolbar, or the Layer Properties Manager. 2 Use the Quadrant object snap to create a line starting from the left side of the part. With polar snap on, move the cursor upward and enter 100 to make the line 100 mm long. Create another 100 mm line on the right side of the part. 104 | Chapter 7 Make Modifications

Section	Page
Contents	3
Index 169	5
Make the Transition from Paper to CAD	7
Draw to Scale	9
Lay Out Your Drawing	11
Organize Drawing Information	13
Establish Drafting Standards	15
Draw Efficiently	17
Draw Accurately	19
View Your Drawing	21
Create Dimensions and Text	23
Modify Your Drawing	25
Introduction	27
Why You Should Use this Guide	28
Tutorials and Command Access	28
Get Additional Information	29
Review and Recall	33
Work with Commands	35
Use the Mouse	36
Cancel a Command	36
Start a Command	36
Undo or Redo Commands	40
Review and Recall	40
Change Views	43
Zoom to Magnify a View	44
Pan to Reposition a View	45
Review and Recall	46
Drawing Setup	49
Start a Drawing	50
Plan the Drawing Units and Scale	52
Understand Models and Layouts	54
Organize Drawings with Layers	56
Tutorial: Tour a Drawing	58
Review and Recall	59
Draw Objects	61
Object Properties Overview	62
Draw Lines	70
Draw Circles and Arcs	73
Review and Recall	74
Precision Drawing	77
Set Grid and Snap Values	78
Draw with Coordinates	80
Snap to Precise Points on Objects	82
Object Snap Descriptions	84
Specify Angles and Distances	85
Review and Recall	88
Make Modifications	91
Select Objects to Edit	92
Erase, Extend, and Trim Objects	93
Duplicate Objects	96
Move and Rotate Objects	99
Fillet Corners	100
Use Editing Aids	115
Analyze Drawings	117
Review and Recall	118
Add Symbols and Hatches	121
Overview of Blocks	122
Insert Blocks	123
Overview of Hatches	125
Insert Hatches or Solid Fills	126
Review and Recall	128
Add Text to a Drawing	131
Create and Modify Text	132
Work with Text Styles	134
Set Text Size for the Viewport Scaling	135
Review and Recall	136
Add Dimensions	139
Dimensions Overview	140
Create Dimensions	141
Use Dimensioning Options	144
Create and Modify Dimension Styles	146
Modify Dimensions	148
Review and Recall	150
Create Layouts and Plots	153
Work with Layouts	154
Choose and Configure Plotters	157
Plot from a Layout	159
Review and Recall	164
Glossary	165

Match case Limit results 1 per page

104

Chapter 7

Make Modifications

Use the Mirror command to mirror the arc using the center points of the left and right circles to

define the mirror line. Again, use SHIFT and right-click to access the object snap menu.

There are often alternative methods for each step. For example, to create the lower arc, you could

have used the Fillet command to fillet the two outer circles with a radius of 250 mm.

Trim the outer-left circle as shown.

The front view of the part is complete. Next, you will use the objects in the front view to create the

top view of the part.

Create the top view

Set the current layer to

Model-Top

. You can use the Layer control on the Layers toolbar, or the

Layer Properties Manager.

Use the Quadrant object snap to create a line starting from the left side of the part. With polar

snap on, move the cursor upward and enter

100

to make the line 100 mm long. Create another

100 mm line on the right side of the part.