Home » Cisco Manuals » Hubs & Switches » Cisco 6513 » Manual Viewer

Cisco 6513 Installation Guide - Page 217

GB GBIC Transceiver

Add to My Manuals
Save this manual to your list of manuals

Page 217 highlights

Appendix B Pluggable Transceiver Modules 1-GB Transceivers Table B-5 GBIC Transceiver Module Cabling Specifications (continued) GBIC Transceiver Model and Product Number 1000BASE-LX/LH (WS-G5486) Interface Connector SC duplex Nominal Wavelength (nm) 1310 Network Cable Type MMF4 Fiber Core Size1 (micron) 62.5 50.0 Modal Bandwidth Cable Distance2 (MHz km) 500 1804 ft (550 m) 400 1804 ft (550 m) 1000BASE-ZX6 (WS-G5487) SC duplex 1550 SMF SMF SMF7 50.0 500 G.6525 - G.6525 - G.6525 - 1804 ft (550 m) 6.2 mi (10 km) 43.5 mi (70 km)8 62.1 mi (100 km) 1. The numbers given for multimode fiber-optic (MMF) cable refer to the core diameter. 2. Cable distances are based on fiber loss. Additional factors, such as the number of splices and the optical quality of the fiber, can affect cabling distances. 3. Use with MMF only. 4. When using an LX/LH GBIC transceiver with 62.5-micron diameter MMF, you must install a mode-conditioning patch cord (CAB-GELX-625 or equivalent) between the GBIC transceiver and the MMF cable on both the transmit and receive ends of the link. The mode-conditioning patch cord is required for link distances less than 328 feet (100 m) or greater than 984 feet (300 m). The mode-conditioning patch cord prevents overdriving the receiver for short lengths of MMF and reduces differential mode delay for long lengths of MMF. 5. ITU-T G.652 SMF as specified by the IEEE 802.3z standard. 6. Use with SMF only. 7. Dispersion-shifted single-mode fiber-optic cable. 8. The minimum link distance for ZX GBICs is 6.2 miles (10 km), when an 8-dB attenuator is installed at each end of the link. Without attenuators, the minimum link distance is 24.9 miles (40 km). Table B-6 lists the fiber loss budgets for the GBIC transceivers. Table B-6 Fiber Loss Budgets for the 1-GB GBIC Transceivers 1-GB GBIC Transceiver Product Number Transmit (dBm) Receive (dBm) WS-G5484 -3 (maximum) 0 (maximum) (1000BASE-SX) -9.5 (minimum) -17 (minimum) WS-G5486 -3 (maximum) -3 (maximum) (1000BASE-LX/LH) -9.5 (minimum) -19 (minimum) WS-G5487 (1000BASE-ZX) 5 (maximum) 0 (minimum) -3 (maximum) -23 (minimum)1 1. The 1000BASE-ZX GBIC transceiver provides a minimum optical power budget of 23 dB. To determine the supported link distance, you need to measure your cable plant with an optical loss test set to verify that the optical loss of the cable plant (including connectors and splices) is less than or equal to this value. The optical measurement must be performed with a 1550 nanometer light source. OL-6265-03 Catalyst 6500 Series Ethernet Modules Installation Guide B-5

Section	Page
Catalyst 6500 Series Ethernet Modules Installation Guide	1
Contents	3
Preface	7
Audience	7
Organization	7
Conventions	8
Statement 1071-Warning Definition	10
Related Documentation	15
Catalyst 6500 Series Switch Chassis Overview	17
Catalyst 6503 Switch	18
Catalyst 6503-E Switch	23
Catalyst 6504-E Switch	27
Catalyst 6506 Switch	31
Catalyst 6506-E Switch	36
Catalyst 6509 Switch	41
Catalyst 6509-E Switch	46
Catalyst 6509-NEB Switch	51
Catalyst 6509-NEB-A Switch	56
Catalyst 6509-V-E Switch	61
Catalyst 6513 Switch	65
Catalyst 6513-E Switch	70
2	75
Ethernet Switching Modules	75
10 and 10/100 Fiber-Based Ethernet Modules	75
WS-X6024-10FL-MT Ethernet Module	76
Figure 2-1 WS-X6024-10FL-MT Ethernet Module Front Panel	76
Table 2-1 WS-X6024-10FL-MT Ethernet Module Features	76
Table 2-2 WS-X6024-10FL-MT Ethernet Module Physical and Environmental Specifications	78
WS-X6148-FE-SFP Ethernet Module	78
Figure 2-2 WS-X6148-FE-SP Ethernet Module Front Panel	78
Table 2-3 WS-X6148-FE-SFP Features	78
Table 2-4 WS-X6148-FE-SFP Physical and Environmental Specifications	80
WS-X6324-100FX-MM and WS-X6324-100FX-SM Ethernet Modules	81
Figure 2-3 WS-X6324-100FX-MM and WS-X6324-100FX-SM Ethernet Modules Front Panel	81
Table 2-5 WS-X6324-100FX-MM and WS-X6324-100FX-SM Ethernet Module Features	81
Table 2-6 WS-X6324-100FX-MM and WS-X6324-100FX-SM Ethernet Modules Physical and Environmental Specifications	83
WS-X6524-100FX-MM Ethernet Module	84
Figure 2-4 WS-X6524-100FX-MM Switching Modules Front Panel	84
Table 2-7 WS-X6524-100FX-MM Features	84
Table 2-8 WS-X6524-100FX-MM Physical and Environmental Specifications	86
10/100 and 10/100/1000 Ethernet Modules	87
WS-X6148-GE-TX and WS-X6148A-GE-TX Ethernet Modules	88
Table 2-9 WS-X6148-GE-TX and WS-X6148A-GE-TX Ethernet Module Variants	88
Figure 2-5 WS-X6148-GE-TX Ethernet Module Front Panel	88
Table 2-10 WS-X6148-GE-TX and WS-X6148A-GE-TX Features	89
Table 2-11 WS-X6148-GE-TX and Variants Physical and Environmental Specifications	91
WS-X6148-RJ21 Ethernet Modules	93
Table 2-12 WS-X6148-RJ21 Ethernet Module Variants	93
Figure 2-6 WS-X6148-RJ-21 Ethernet Module Front Panel	93
Table 2-13 WS-X6148-RJ-21 Ethernet Modules Features	93
Table 2-14 WS-X6148-RJ-21 Physical and Environmental Specifications	96
WS-X6148-RJ-45 and WS-X6148A-RJ-45 Ethernet Modules	97
Table 2-15 WS-X6148-RJ-45 and WS-X61248A-RJ-45 Ethernet Modules and Variants	97
Figure 2-7 WS-X6148-RJ-45 Ethernet Module Front Panel	97
Table 2-16 WS-X6148-RJ-45 and WS-X6148A-RJ-45 Ethernet Modules Features	98
Table 2-17 WS-X6148-RJ-45 Ethernet Modules Physical and Environmental Specifications	101
WS-X6148X2-RJ-45 and WS-X6148X2-45AF Ethernet Modules	103
Table 2-18 WS-X6148X2-RJ-45 and the WS-X6148X2-45AF Ethernet modules	103
Figure 2-8 WS-X6148X2-RJ-45 Ethernet Module Front Panel	103
Figure 2-9 WS-F6K-48X2-SPLTR Splitter Panel	103
Table 2-19 WS-X6148X2-RJ-45 and WS-X6148X2-45AF Ethernet Modules Features	104
Table 2-20 WS-X6148X2-RJ-45 Physical and Environmental Specifications	107
WS-X6196-RJ-21 and WS-X6196-21AF Ethernet Modules	108
Table 2-21 WS-X6196-RJ-21 Modules	108
Figure 2-10 WS-X6196-RJ-21 Switching Module Front Panel	108
Table 2-22 WS-X6196-RJ-21 and WS-X6196-21AF Ethernet Modules Features	108
Table 2-23 WS-X6196-RJ-21 and WS-X6196-21AF Ethernet Modules Physical and Environmental Specifications	111
WS-X6348-RJ21V Ethernet Module	112
Figure 2-11 WS-X6348-RJ21V Switching Module	112
Table 2-24 WS-X6348-RJ21V Features	112
Table 2-25 WS-X6348-RJ21V Physical and Environmental Specifications	114
WS-X6348-RJ45 and WS-X6348-RJ45V Ethernet Modules	114
Table 2-26 WS-X6348-RJ45 Modules	114
Figure 2-12 WS-X6348-RJ45 and WS-X6348-RJ45V Ethernet Modules Front Panel	114
Table 2-27 WS-X6348-RJ45 and WS-X6348-RJ45V Ethernet Modules Features	115
Table 2-28 WS-X6348-RJ45 and WS-X6348-RJ45V Physical and Environmental Specifications	117
WS-X6516-GE-TX Ethernet Module	118
Figure 2-13 WS-X6516-GE-TX Ethernet Module	118
Table 2-29 WS-X6516-GE-TX Ethernet Module Features	118
Table 2-30 WS-X6516-GE-TX Ethernet Module Physical and Environmental Specifications	120
WS-X6548-GE-TX, WS-X6548-GE-45AF, and WS-X6548V-GE-TX Ethernet Modules	121
Table 2-31 WS-X6548-GE-TX Ethernet Module Variants	121
Figure 2-14 WS-X6548-GE-TX Ethernet Module Front Panel	121
Table 2-32 WS-X6548-GE-TX Modules Features	121
Table 2-33 WS-X6548-GE-TX and Variants Physical and Environmental Specifications	124
WS-X6548-RJ-21 Ethernet Module	125
Figure 2-15 WS-X6548-RJ-21 Ethernet Module Front Panel	125
Table 2-34 WS-X6548-RJ-21 Ethernet Module Features	125
Table 2-35 WS-X6548-RJ-21 Physical and Environmental Specifications	127
WS-X6548-RJ-45 Ethernet Module	128
Figure 2-16 WS-X6548-RJ-45 Switching Module Front Panel	128
Table 2-36 WS-X6548-RJ-45 Features	128
Table 2-37 WS-X6548-RJ-45 Physical and Environmental Specifications	130
WS-X6748-GE-TX Ethernet Module	132
Figure 2-17 WS-X6748-GE-TX Ethernet Module Front Panel	132
Table 2-38 WS-X6748-GE-TX Ethernet Module Features	132
Table 2-39 WS-X6748-GE-TX Physical and Environmental Specifications	135
1-Gigabit Ethernet Modules	137
WS-X6408A-GBIC	137
Figure 2-18 WS-X6408A-GBIC Ethernet Module Front Panel	137
Table 2-40 WS-X6408A-GBIC Ethernet Module Features	137
Table 2-41 WS-X6408A-GBIC Physical and Environmental Specifications	140
WS-X6416-GBIC	140
Figure 2-19 WS-X6416-GBIC Ethernet Module Front Panel	140
Table 2-42 WS-X6416-GBIC Features	140
Table 2-43 WS-X6416-GBIC Ethernet Module Physical and Environmental Specifications	142
WS-X6516-GBIC and WS-X6516A-GBIC	143
Figure 2-20 WS-X6516-GBIC and WS-X6516A-GBIC Ethernet Modules Front Panel	143
Table 2-44 WS-X6516-GBIC and WS-X6516A-GBIC Features	143
Table 2-45 WS-X6516-GBIC and WS-X6516A-GBIC Physical and Environmental Specifications	145
WS-X6724-SFP	148
Figure 2-21 WS-X6724-SFP Ethernet Module Front Panel	148
Table 2-46 WS-X6724-SFP Ethernet Module Features	148
Table 2-47 WS-X6724-SFP Ethernet Module Physical and Environmental Specifications	150
WS-X6748-SFP	152
Figure 2-22 WS-X6748-SFP Switching Module Front Panel	152
Table 2-48 WS-X6748-SFP Features	152
Table 2-49 WS-X6748-SFP Physical and Environmental Specifications	155
WS-X6816-GBIC	157
Figure 2-23 WS-X6816-GBIC Switching Module Front Panel	157
Table 2-50 WS-X6816-GBIC Ethernet Module Features	157
Table 2-51 WS-X6816-GBIC Physical and Environmental Specifications	160
10-Gigabit Ethernet Modules	161
WS-X6704-10GE Ethernet Module	161
Figure 2-24 WS-X6704-10GE Ethernet Module Front Panel	161
Table 2-52 WS-X6704-10GE Ethernet Module Features	161
Table 2-53 WS-X6704-10GE Ethernet Module Physical and Environmental Specifications	164
WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet Modules	166
Figure 2-25 WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet Module Front Panel	166
Table 2-54 WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet Module Features	166
Table 2-55 WS-X6708-10G-3C and WS-X6708-10G-3CXL Ethernet Module Physical and Environmental Specifications	169
WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Modules	170
Figure 2-26 WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Module Front Panel	170
Table 2-56 WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Module Features	170
Table 2-57 WS-X6716-10G-3C and WS-X6716-10G-3CXL Ethernet Module Physical and Environmental Specifications	173
WS-X6716-10T-3C and WS-X6716-10T-3CXL Ethernet Modules	174
Figure 2-27 WS-X6716-10T-3C and WS-X6716-10T-3CXL Ethernet Module Front Panel	174
Table 2-58 WS-X6716-10T-3C and WS-X6716-10T-3CXL Ethernet Module Features	174
Table 2-59 WS-X6716-10T-3C and WS-X6716-10T-3CXL Ethernet Module Physical and Environmental Specifications	177
Installing Ethernet Switching Modules	179
Safety	179
Installing an Ethernet Switching Module	180
Required Tools	180
Installing an Ethernet Switching Module	180
Removing an Ethernet Switching Module	188
Installing Pluggable Transceivers	189
Installing GBIC Transceivers	189
Installing SFP Transceivers	192
Installing 10GBASE XENPAK Transceivers	196
Installing 10GBASE X2 Transceivers	197
Attaching the Network Interface Cables	200
Attaching Optical Network Interface Cables	200
Mode-Conditioning Patch Cord	201
Connecting Transceivers to a Copper Network	203
Verifying the Installation	203
Verifying Newly Installed Modules	204
Checking Connectivity	205
What To Do After Installing Modules and Verifying Connectivity	205
Ethernet Module Daughter Cards	207
PoE Daughter Cards	207
Centralized and Distributed Forwarding Daughter Cards	209
Pluggable Transceiver Modules	213
100-MB Transceivers	213
1-GB Transceivers	215
1-GB GBIC Transceivers	216
1-GB SFP Transceivers	218
10-GB Transceivers	220
XENPAK Transceivers	221
X2 Transceivers	224
WDM Transceivers	227
ESD Precautions	235
Attaching Your ESD Grounding Strap	235

Match case Limit results 1 per page

B-5

Catalyst 6500 Series Ethernet Modules Installation Guide

OL-6265-03

Appendix B

Pluggable Transceiver Modules

1-GB Transceivers

Table B-6

lists the fiber loss budgets for the GBIC transceivers.

1000BASE-LX/LH

(WS-G5486)

SC duplex

1310

MMF

SMF

62.5

50.0

G.652

500

400

500

—

1804 ft (550 m)

6.2 mi (10 km)

1000BASE-ZX

(WS-G5487)

SC duplex

1550

SMF

G.652

—

43.5 mi (70 km)

62.1 mi (100 km)

The numbers given for multimode fiber-optic (MMF) cable refer to the core diameter.

Cable distances are based on fiber loss. Additional factors, such as the number of splices and the optical quality of the fiber, can affect cabling

distances.

Use with MMF only.

When using an LX/LH GBIC transceiver with 62.5-micron diameter MMF, you must install a mode-conditioning patch cord (CAB-GELX-625 or

equivalent) between the GBIC transceiver and the MMF cable on both the transmit and receive ends of the link. The mode-conditioning patch cord

is required for link distances less than 328 feet (100 m) or greater than 984 feet (300 m). The mode-conditioning patch cord prevents overdriving

the receiver for short lengths of MMF and reduces differential mode delay for long lengths of MMF.

ITU-T G.652 SMF as specified by the IEEE 802.3z standard.

Use with SMF only.

Dispersion-shifted single-mode fiber-optic cable.

The minimum link distance for ZX GBICs is 6.2 miles (10 km), when an 8-dB attenuator is installed at each end of the link. Without attenuators,

the minimum link distance is 24.9 miles (40 km).

Table B-5

GBIC Transceiver Module Cabling Specifications (continued)

GBIC Transceiver

Model and Product

Number

Interface

Connector

Nominal

Wavelength

(nm)

Network

Cable Type

Fiber Core

Size

(micron)

Modal Bandwidth

(MHz km)

Cable Distance

Table B-6

Fiber Loss Budgets for the 1-GB GBIC Transceivers

1-GB GBIC Transceiver

Product Number

Transmit (dBm)

Receive (dBm)

WS-G5484

(1000BASE-SX)

–3 (maximum)

–9.5 (minimum)

0 (maximum)

–17 (minimum)

WS-G5486

(1000BASE-LX/LH)

–3 (maximum)

–9.5 (minimum)

–3 (maximum)

–19 (minimum)

WS-G5487

(1000BASE-ZX)

5 (maximum)

0 (minimum)

–3 (maximum)

–23 (minimum)

The 1000BASE-ZX GBIC transceiver provides a minimum optical power budget of

23 dB. To determine the supported link distance, you need to measure your cable plant

with an optical loss test set to verify that the optical loss of the cable plant (including

connectors and splices) is less than or equal to this value. The optical measurement

must be performed with a 1550 nanometer light source.