Home » Dell Manuals » Servers » Dell Force10 E1200i » Manual Viewer

Dell Force10 E1200i Installing and Maintaining the E1200i System - Page 79

System Specifications, E1200i AC Chassis Physical Design

View all Dell Force10 E1200i manuals

Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

D System Specifications This appendix contains two major sections: • E1200i AC Chassis Physical Design • E1200i AC System Power Requirements • E1200i DC Chassis Physical Design • E1200i DC System Power Requirements • Environmental Specifications • Agency Compliance E1200i AC Chassis Physical Design Parameter Height Width Depth (without cable management system) Chassis weight with factory-installed components (backplane and air filter) Weight fully loaded (backplane, air filter, 2 fan trays, 10 SFMs, RPMs, and 14 line cards) Mounting Rack clearance required Thermal Output Maximum for fully loaded chassis Minimum for chassis with one 48-port 1GE line card Specifications 42 inches (106.68 cm) 17.40 inches (44.20 cm) 22.25 inches (56.51 cm) 139 pounds (approx.) (63.05kg) 394 pounds (approx.) (178.7 kg) Attached rack mount brackets are factory set for front mounting in a standard 19-inch rack. Mounting brackets are adjustable for center and rear mounting. Optional brackets are available for front or center mounting in a 23-inch rack or cabinet. Front: 18 inches Rear: 20 inches 7,784W (26,578BTU/HR) 1,450W (4,951 BTU/HR) System Specifications | 79

Section	Page
About This Guide	7
Information Symbols and Warnings	7
Related Publications	8
The E1200 System	9
Operating Overview	9
Site Preparation	15
Site Selection Criteria	15
Rack Mounting	16
Cabinet Placement	16
Power	16
Fans and Airflow	17
Storing Components	17
Installing the AC Chassis	19
Unpacking the E1200 System	19
Installing the Equipment Rack Shelf Bar	19
Standard Front Chassis Mounting	20
Installing the Chassis into an Equipment Cabinet	21
Installing the DC Chassis	23
Unpacking the E1200 System	23
Installing the Equipment Rack Shelf Bar	23
Standard Front Chassis Mounting	24
Installing the Chassis into an Equipment Cabinet	25
Installing Fan Trays	27
Installing AC Power Supplies	29
Securing the Chassis Ground	30
Installing Power Supplies	30
AC Power Supply and Fan Operability Test	31
Installing DC Power Supplies	33
Cable and Connector Requirements	34
Installing DC PEMs	34
DC Power Supply and Fan Operability Test	38
Installing RPMs, Line Cards, and SFMs	41
Unpacking an RPM or Line Card	41
Important Points to Remember	41
Installing Line Cards and RPMs	42
RPMs	42
Line Cards	42
Blank Panels	43
Preparing and Installing RPMs and Line Cards	43
Installing a Second RPM	44
RPM Label and LEDs	45
Line Card LEDs	46
Installing Switch Fabric Modules (SFMs)	46
SFM Front Panel and LEDs	47
Line Card Cable Management Systems	47
RPM Ports and Cables	49
RPM Ports	49
Connecting the Console and Auxiliary Ports	49
Cable and Adapter Pin Assignments	50
Accessing the Console with a DB-9 Adapter	51
Accessing the Console with a DB-25 Adapter	51
Accessing the Auxiliary Port by Modem	52
Accessing the 10/100 Ethernet Management Port	52
Powering Up	53
Preparation	53
Supplying Power - AC	54
Supplying Power - DC	54
Booting to the CLI Prompt	54
Booting from the BOOT_USER Prompt	55
Removing and Replacing Components	57
Removing and Replacing Fan Trays	57
Removing and Replacing AC Power Supplies	58
Remove an AC Power Supply in a non-redundant installation	59
Remove an AC Power Supply in a redundant installation	59
Removing and Replacing DC Power Supplies	59
Remove a DC Power Supply	60
Removing and Replacing RPMs, Line Cards, or SFMs	61
Removing and Replacing line cards or RPMs	61
Removing and Replacing SFMs	62
Removing and Replacing the Air Filter	63
Using a Flash Memory Card	65
External Flash Memory Card Overview	65
Inserting the External Flash Memory Card	65
Removing the External Flash Memory Card	66
Formatting an External Flash Card	66
Copying Files to the External Flash	67
Displaying Files Stored on the External Flash	67
System Boot	69
The System Boot Process	69
System Boot	69
Booting from the BOOT_USER Prompt	69
Alarms	75
Power Supplies and Alarms	76
AC Power Supplies and Alarms	77
SFMs and Alarms	77
System Specifications	79
E1200i AC Chassis Physical Design	79
E1200i AC System Power Requirements	80
E1200i DC Chassis Physical Design	80
E1200i DC System Power Requirements	80
Environmental Specifications	81
Agency Compliance	81
Safety Standards and Compliance Agency Certifications	83
Electromagnetic Emissions	83
Immunity	83
Product Recycling and Disposal	84
Technical Support	85
The iSupport Website	85
Accessing iSupport Services	85
Contacting the Technical Assistance Center	86
Requesting a Hardware Replacement	87