Dell PowerVault 56F Dell PowerVault 56F 16-Port Fibre Channel Switch Inst - Page 110

Reattach external cabling to the power supply.

Get Dell PowerVault 56F PDF manuals and user guides View all Dell PowerVault 56F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

To remove the power supply, you must perform the following steps. 1. Remove any external cabling attached to the power supply. 2. Pull out and lift up the metal handle from the top of the power supply unit; see Figure 6-1. 3. Gently pull the unit out. handle 1. Slide the new power supply unit into its slot until the unit connects to the back panel. 2. Lock the metal handle into the power supply by pushing the handle down and sliding it up into place. 3. Reattach external cabling to the power supply. The switch automatically runs power-on self-test (POST) on a PowerVault 56F switch because all the power was off. 4. Check for error messages by issuing the Telnet command. 6-2 Installation and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
6-2
Installation and Troubleshooting Guide
Dzƽ¼³Ä·»Í²·¸½#²´·Áº%%¶Å
To remove the power supply, you must perform the following steps.
µ¹°³´²±·¸$ÂÀ»¸ÃÀÄƾ½º»È¸¾¸ÄÅÉÀøÁÌÄÄÆ˸̻º¿¸Å»¸¾¸,ÅÉÀÃ.¾ÌÆ¿¸:?4¸Á¿ÅÃ)
¾ÈÀ¸ÁËÁ¿ÀǸ½Å»ÊºÈÌÃÀ¼¸Éº¿Â¸Å»À¸ÄÅÉÀøÁÌÄÄÆË"¸ËÅ̸ÇÌÁ¿¸¿Ìû¸ÅÊʸ¿ÂÀ¸Áɺ¿½Â+Á¸
ÄÅÉÀÃϸ4Åø¾¸,ÅÉÀÃ.¾ÌÆ¿¸:?4¸Á¿ÅþÈÀ¸ÁËÁ¿ÀǸ½Å»ÊºÈÌÃÀ¼¸Éº¿Â¸¼Ì¾Æ¸ÄÅÉÀø
ÁÌÄÄƺÀÁ"¸ËÅ̸¼Å¸»Å¿¸»ÀÀ¼¸¿Å¸¿Ìû¸ÅÊʸ¿ÂÀ¸¾½¿ºÍÀ¸ÄÅÉÀøÁÌÄÄÆ˸ÎÀÊÅÃÀ¸ÃÀÄƾ½)
º»È¸¿ÂÀ¸º»¾½¿ºÍÀ¸ÄÅÉÀøÁÌÄÄÆËÏ
1.
Remove any external cabling attached to the power supply.
2.
Pull out and lift up the metal handle from the top of the power supply unit; see
Figure 6-1.
3.
Gently pull the unit out.
±²³´µ¶·Ã¹¸º··-¶!¼,²Ç³·Áƶ·»¼½¶µ·Ä´ÏÏÀ°
)³¾»µ¶¶¼³Ä·»Í²·¸½#²´·Áº%%¶Å
1.
Slide the new power supply unit into its slot until the unit connects to the back
panel.
2.
Lock the metal handle into the power supply by pushing the handle down and
sliding it up into place.
3.
Reattach external cabling to the power supply.
The switch automatically runs power-on self-test (POST) on a PowerVault 56F
switch because all the power was off.
4.
Check for error messages by issuing the
Telnet
command.
handle