Dell PowerVault 56F Dell PowerVault 56F 16-Port Fibre Channel Switch Inst - Page 139

fspfShow, bcastShow, portLogShow, LSDbAllShow

Get Dell PowerVault 56F PDF manuals and user guides View all Dell PowerVault 56F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 139 highlights

HLO LSDB MCAST INPORT (2) The input port in the IU received by the path selection task is out of range. Check that all paths and routing tables are correct. If they are not correct, reboot the local switch. MSG (2) The path selection task has received an unknown message from another task. Check that all paths and routing tables are correct. If they are not, reboot the neighbor switch. Check the paths and routes again. If they are still incorrect, reboot the local switch. REMDOMAIN (2) The message received from a neighbor switch has a source domain ID out of range. Check that all paths and routing tables are correct. If they are not, reboot the neighbor switch. Check the paths and routes again. If they are still incorrect, reboot the local switch. SCN (3) The path selection task has received a State Change Notification message that it does not recognize. Check that all paths and routing tables are correct. If they are not, reboot the local switch. VERSION (2) The FSPF protocol version running on the local switch is lower than a neighbor's switch. Check the protocol version on both switches using the fspfShow command. If the two versions differ, update the software on the local switch. INVHLO (1) The path selection task has received a HELLO message with an invalid parameter from a neighbor switch. Check that all paths and routing tables are correct. If they are not, reboot the neighbor switch. Check the paths and routes again. If they are still incorrect, reboot the local switch. LSID (2) A Link State Record received as part of a Link State Update has an out of range domain ID. Check that all paths are correct. If any path is missing to any switch in any part of the fabric, reboot the switch with the missing path. ADDBRANCH (2) A branch is being added to a broadcast or multicast tree, but the parameters are incorrect. If this is caused by a configuration command, check the parameter values. Otherwise, check the broadcast tree with the bcastShow command. If the tree is incorrect, reboot the local switch. ADDPORT (3) A multicast routing table programming failed. Run the portLogShow command. Contact Customer Support. NOPARENT (2) An error occurred while comput- Run the LSDbAllShow command. Coning a broadcast or multicast tree. tact Customer Support. NOPARENTLS An error occurred while comput- Run the LSDbAllShow command. Con- R (2) ing a broadcast or multicast tree. tact Customer Support. support.dell.com Error Messages A-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
support.dell.com
Error Messages
A-3
INPORT (2)
The input port in the IU received
by the path selection task is out
of range.
Check that all paths and routing tables are
correct. If they are not correct, reboot the
local switch.
MSG (2)
The path selection task has
received an unknown message
from another task.
Check that all paths and routing tables are
correct. If they are not, reboot the neigh-
bor switch.
Check the paths and routes again. If they
are still incorrect, reboot the local switch.
REMDOMAIN
(2)
The message received from a
neighbor switch has a source
domain ID out of range.
Check that all paths and routing tables are
correct. If they are not, reboot the neigh-
bor switch.
Check the paths and routes again. If they
are still incorrect, reboot the local switch.
SCN (3)
The path selection task has
received a State Change Notifica-
tion message that it does not
recognize.
Check that all paths and routing tables are
correct. If they are not, reboot the local
switch.
VERSION (2)
The FSPF protocol version run-
ning on the local switch is lower
than a neighbor
’
s switch.
Check the protocol version on both
switches using the
fspfShow
command.
If the two versions differ, update the soft-
ware on the local switch.
HLO
INVHLO (1)
The path selection task has
received a HELLO message with
an invalid parameter from a
neighbor switch.
Check that all paths and routing tables are
correct. If they are not, reboot the neigh-
bor switch.
Check the paths and routes again. If they
are still incorrect, reboot the local switch.
LSDB
LSID (2)
A Link State Record received as
part of a Link State Update has
an out of range domain ID.
Check that all paths are correct. If any
path is missing to any switch in any part of
the fabric, reboot the switch with the
missing path.
MCAST
ADDBRANCH
(2)
A branch is being added to a
broadcast or multicast tree, but
the parameters are incorrect.
If this is caused by a configuration
command, check the parameter values.
Otherwise, check the broadcast tree with
the
bcastShow
command. If the tree is
incorrect, reboot the local switch.
ADDPORT (3)
A multicast routing table pro-
gramming failed.
Run the
portLogShow
command. Con-
tact Customer Support.
NOPARENT (2)
An error occurred while comput-
ing a broadcast or multicast tree.
Run the
LSDbAllShow
command. Con-
tact Customer Support.
NOPARENTLS
R (2)
An error occurred while comput-
ing a broadcast or multicast tree.
Run the
LSDbAllShow
command. Con-
tact Customer Support.
È¿ÉÀ¶·0¹¸º··+µµ¼µË
±²³´µ¶·µ¸¹º»
À¾Ëôµ
"ÎξÎ
ºµ*µÎ¼·¸
"Á¹´²¿²·¼¾¿
)»·¼¾¿